Craftsman 21513 Support Question
Craftsman 21513 Support Question
Find answers below for this question about Craftsman 21513 - 2 x 42 in. Belt/6 Disc Sander.Need a Craftsman 21513 manual? We have 1 online manual for this item!
Question posted by Anonymous-54214 on March 19th, 2012
How Much Did This Cost New
The person who posted this question about this Craftsman product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by 1stLadyDawn on March 19th, 2012 12:32 PM
1stLadyDawn
Member since:
January 25th, 2012 Points: 821,520
Member since:
January 25th, 2012 Points: 821,520
Related Craftsman 21513 Manual Pages
Operation Manual - Page 1
www.sears.com/craftsman
20067.01 Draft (11/07/03)
Operator's Manual
I
x 42" Belt
SANDER
Model No. 351.215130
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Operation Manual - Page 2
... workmanship within one year from the date of purchase, Sears will at its option repair or replace it was not designed.
• Disconnect tool when changing belt or abrasive disc. • Avoid accidental start-up. This warranty gives you specific legal rights and you are NOT safety glasses. • Wear face mask or...
Operation Manual - Page 3
... specific limitations,
• Use recommended accessories (refer to order replacement parts. ATTACH ABRASIVE DISC TO ALUMINUM DISC
Refer to Figure 2, • Set the disc table at all times when tool is pasted evenly on tool.
Check for :
A Disc Table B Abrasive Disc
C Miter Gauge Assembly D 1" Belt E Belt Table
Parts bag (Part No. 21489.00) includes: horizontal stop , two knobs, one...
Operation Manual - Page 4
...by a single
pole locking rocker switch.
POWER SOURCE WARNING: Do not connect sander to determine the minimum wire size (A.W.G.) extension cord.
• Use only 3-wire...to a permanent electrical ground such as a positive stop bar with the belt housing adjusted to whether the tool is properly grounded. • This tool is properly grounded.
Make Sure
Grounding Lug _
3-Prong Plug.
\_...
Operation Manual - Page 5
... is controlled by a qualified electrician. The power supply to 45 ° 1'/2"
Disc speed Base dimensions
3500 RPM 81/,x 71/8"
Switch
SP, Locking rocker
Weight
30 Ibs
WARNING: Operation of the tool. DESCRIPTION
Craftsman 2 x 6" Belt and Disc Sander has a 2" x 42"
belt and 6" disc for contour sanding. Belt speed is not recommended. Safety goggles are tight and have...
Operation Manual - Page 6
... parallel to desired angle. The arrow should point in the direction of abrasive belt, disc and all moving parts.
• For optimum performance, do not stall motor or reduce speed. Idler Wheel
Handle
Figure 7 - MOUNT SANDER
During operation the sander may be replaced when worn, torn, or glazed.
• Loosen and remove two knobs...
Operation Manual - Page 7
... centered on the wheels. Hold the position of the bolt with the table. Remove belt platen.
• Replace belt cover and knobs. Contour Sanding
SHARPENING
Refer to Figure 11, • Adjust belt table to table. Adjusting Belt Housing
Lock Bolt
7
Use belt sander to notch the back of an auxiliary piece of wood. • Using a C-clamp...
Operation Manual - Page 8
... at desired angle, lock it easier to feed the work and holding belt table on sander. WARNING: Disconnect sander from alu- minum disc. Select the proper abrasive disc and apply to aluminum disc. • Additional abrasive discs are permanently lubricated at 90 ° to the belt with dust collector to keep dust from power source before attempting to...
Operation Manual - Page 9
Use parts
list to repair motor may create a hazard unless repair is done by a qualified service technician. KEEP TOOL IN REPAIR • If power cord is available at your nearest Sears store.
9 Any attempt to order parts. Repair service is worn, cut, or damaged ...
Operation Manual - Page 10
... open connection
3. Rewire motor as per wiring diagram, see Operation
section, "Horizontal Belt Sanding"
10 Power line overloaded with
2. General overloading of
decrease in motor or... bolt, see
Installation section, "Electrical Connections"
Motor fails to
while operating
workpiece
Abrasive belt runs off top whee, 1. Replace capacitor 1. Increase wire sizes, or reduce length ...
Operation Manual - Page 13
.... 67-72)
5-0.8 x 12mm Pan Head Screw*
2
Pointer
1
1 x 42" Abrasive Belt
1
Parts Bag
1
Operator's Manual
1
Recommended Accessories Abrasive Belts 2 x 42" (Fine) Abrasive Belts 2 x 42" (Medium)
t_ Abrasive Belts 2 x 42" (Coarse) Abrasive Disc 6" (Assorted) Abrasive Belts 1 x 42" (Fine) Abrasive Belts 1 x 42" (Medium)
t, Abrasive Belts 1 x 42" (Course) t_ Abrasive Cleaner
9-28480 9-28481...
Similar Questions
How To Replace New Return Spring On 42' Craftsman Mower Deck?
I have a 15.5 h.p craftsman tractor model number 917529550 and can't find any info on how to replace...
I have a 15.5 h.p craftsman tractor model number 917529550 and can't find any info on how to replace...
(Posted by edesloover1 8 years ago)
Remote On Shop Vac Wont Work After Installing New Battery
The Battery On My Remote For My Shop Vac Needed To Be Replaced which Has Been Done With The Same Bat...
The Battery On My Remote For My Shop Vac Needed To Be Replaced which Has Been Done With The Same Bat...
(Posted by anthonyservidio 9 years ago)
Why Is My Brand New Craftsman Saber Saw Unable To Cut A Straight Line.it Also Cu
(Posted by csullivan2 10 years ago)
New Blade
Where can I buy a new balde. I coun't fint in Internet. Thanks for your hlep
Where can I buy a new balde. I coun't fint in Internet. Thanks for your hlep
(Posted by beneva82 11 years ago)
Belt Change
How do I change the belt on my sander? Model 531.215140 Thanks
How do I change the belt on my sander? Model 531.215140 Thanks
(Posted by rmuskat 13 years ago)