Craftsman 21514 - Belt & Disc Sander Support and Manuals
Get Help and Manuals for this Craftsman item
View All Support Options Below
Free Craftsman 21514 manuals!
Problems with Craftsman 21514?
Ask a Question
Free Craftsman 21514 manuals!
Problems with Craftsman 21514?
Ask a Question
Most Recent Craftsman 21514 Questions
Parts
Where can I buy a second table for the 21524 belt/disk sander. Part number 23655.00 Dan Mazel Bill...
Where can I buy a second table for the 21524 belt/disk sander. Part number 23655.00 Dan Mazel Bill...
(Posted by ss90680 12 years ago)
Belt Change
How do I change the belt on my sander? Model 531.215140 Thanks
How do I change the belt on my sander? Model 531.215140 Thanks
(Posted by rmuskat 12 years ago)
Popular Craftsman 21514 Manual Pages
Operation Manual - Page 1
Operator's Manual
CRRFISMRN °
4 x 36" Belt 6" Disc
SANDER Model No.
351.215141
CAUTION: Read and follow
all Safety Rules and Operating Instructions before First Use
of this manual with tool.
Sears, Roebuck and Co., Hoffman
www.sears.com/craftsman
30657.00 Draft (04/07/09)
Estates, IL 60179 U.S.A. Keep this Product.
Operation Manual - Page 2
... Wear face mask or dust mask if operation is damaged should be properly repaired or replaced. Warranty Safety Rules Unpacking Assembly Installation Operation Maintenance Troubleshooting Parts Illustration and List Espa_ol
2 2-3
3 3-4 4-5 5-8
8 9 10-13 14-22
ONE-YEAR FULL WARRANTY ON CRAFTSMAN TOOL If this Craftsman tool fails due to a defect in damp or wet locations. If this...
Operation Manual - Page 3
...SANDER Refer to order replacement parts. Allow room so that neither operators nor bystanders will need to be fastened to a firm, level surface. • Make sure there is being used. E
_'B Figure 1 - Use this manual... Sander
6" 24"
Refer to the instructions.
WARNING: Do not attempt to operate tool until it stuck in the work.)
• Support workpiece with miter gauge, belt ...
Operation Manual - Page 4
... press on voltages which are not understood or if in position. Replace disc cover.
Using Table with Belt
Figure 4 - Remove Cover and Attach Abrasive Disc ATTACH TABLE Refer to Figures 7, 8 and 9, pages 4 and 5.
Running the unit on firmly and evenly. GROUNDING INSTRUCTIONS
WARNING: Improper connection of equipment grounding conductor can result in any...
Operation Manual - Page 5
... ground, grounding means must be replaced with a properly grounded 3-prong receptacle installed in voltage and loss of power.
• Wires of the extension cord must be performed by a qualified electrician. DESCRIPTION
The Craftsman Belt and Disc Sander is available for guiding the workpiece at 120 volts. SPECIFICATIONS Belt size
Belt platen area Belt speed Disc diameter Disc speed...
Operation Manual - Page 6
... or replacing any angle in accordance with disc.
° Never push a sharp corner of the workpiece rapidly against the belt or disc.
To turn switch ON and OFF again.
NOTE: Should the key be removed from the switch at Sears retail stores or catalog. Belt should be tightened securely.
° Make sure all moving parts...
Operation Manual - Page 7
...belt.
Use back stop to belt assembly using the two bolts. • Idler drum can be tilted for both hands; Position table on flat portion of sander...support workpiece when sanding on the
disc or on idler drum portion of long workpieces with the belt assembly in the horizontal position. • Remove table and stud from belt assembly. • Tilt belt... setting miter gauge square to belt ...
Operation Manual - Page 8
... Sears store.
8
Use soap and water to order parts. KEEP TOOL IN REPAIR
• If power cord is available at the factory. Select the desired abrasive disc and apply to tension belt. • Check tracking.
Repair service is worn, cut, or damaged in this tool are available (See Recommended Accessories, page 13).
• Replace disc cover. center belt...
Operation Manual - Page 9
... in power line
Motor fails to workpiece
Abrasive belt runs off top Not tracking properly wheel
CORRECTIVE ACTION...of motor decreases rapidly with lights, appliances and other motors
2. Install correct fuses or circuit breakers
4. Open circuit in motor or... Inspect all lead connections on motor for proper voltage 2. Replace switch 4. Defective capacitor
Motor will not start ; Power...
Operation Manual - Page 10
Replacement Parts Illustration for Belt Housing
11
,..b
o
35 34
37 36
20 16
\ 39 Model 351.2151 41
Figure 17 -
Operation Manual - Page 11
... 1 12 5 1 2 1 1 1 1 1 1 1 1 2 2 1 1 8 1 2
KEY iiO. PART NO. 23 STD840508 24 STD870516 25 STD863510 26 N/A 27 23695.00 28 STD852005 29 STD863508 30 23696.00 31 STD851006 32 ... Flat Washer* 6mm Lock Washer* 6-1.0x15mm Socket Head Bolt Drive Drum 8-1.25 x 10mm Set Screw Abrasive belt
Ball Bearing 6000ZZ* Bearing Plate Idler Assembly Spring Tension Lever 6-1.0 x 20mm Socket Head Bolt* Stud
QTY. 1 2 1 1 ...
Operation Manual - Page 12
Replacement Parts Illustration for Motor and Disc
8
,,,,,.L
1
44 Model 351.21 5141
Figure 18 -
Operation Manual - Page 13
... 23672.00 FooBt
1 35 N/A
Tube
1 36 N/A
DusCt hute
10 37 23664.00 Wrench
10 38 STD8634104-0.7x 10ramPanHeadBolt*
4 39 STD8510044mmFlatWasher*
1 4O N/A
BottomPlate
6 41 23676.00 V-Belt
2 42 23677.00 MotoPr ulley 2 43 23678.00 Nut
8 44 23679.00 Moto(rincludeKseyNo4. 8) 2 45 STD836025 10-1.x525ramHexHeadBolt*
1 46 STD85101010ramFlatWasher*
1 47 STD841015 10-1.5raHmexNut*
3 48...
Operation Manual - Page 24
...)
Call anytime, day or night (U.S.A. For the replacement parts, accessories and owner's manuals that you need to do-it ! of home appliances and items like vacuums, lawn equipment, and electronics, call anytime for the location of your nearest
Sears Parts & Repair Service Center
1-800-488-1222 (U.S.A.) 1-800-469-4663 (Canada)
www.sears.com
www.sears.ca
To purchase a protection agreement on...
Craftsman 21514 Reviews
We have not received any reviews for Craftsman yet.