Craftsman 21500 - Oscillating Spindle Sander Support and Manuals
Get Help and Manuals for this Craftsman item
View All Support Options Below
Free Craftsman 21500 manuals!
Problems with Craftsman 21500?
Ask a Question
Free Craftsman 21500 manuals!
Problems with Craftsman 21500?
Ask a Question
Most Recent Craftsman 21500 Questions
Are All Parts Available For The 21500?
The Sears 351 215000 Drum Sander is not available anymore. Are all of the parts available?
The Sears 351 215000 Drum Sander is not available anymore. Are all of the parts available?
(Posted by sherm54806 9 years ago)
Miles?
i have a lts 1500 craftsman riding lawn mower, how many miles does it get to the gallon
i have a lts 1500 craftsman riding lawn mower, how many miles does it get to the gallon
(Posted by alyssamalcolm 11 years ago)
I Have A Lt 1500 And Need To Obtain A Diagram Of The Carb And Throttle
(Posted by tjsullivan51 12 years ago)
Craftsman Lt 1500
my craftsman lt 1500 will start but will not move forward in drive or vice versa
my craftsman lt 1500 will start but will not move forward in drive or vice versa
(Posted by z2abrown 12 years ago)
Popular Craftsman 21500 Manual Pages
Operation Manual - Page 1
Keep this Product. Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. SAFETY
ASSEMBLY
OPERATION
MAINTENANCE
Operator's Manual
Oscillating Spindle
SANDER Model No.
351.215000
CAUTION: Read and follow
all Safety Rules and Operating Instructions before First Use of this manual with tool. www.sears.com/craftsman
25759.00 Draft (01/22/08)
PARTS LIST
ESPAÑOL
Operation Manual - Page 2
... out of purchase. Check for commercial or rental purposes, this type of the instructions and precautions before switching machine on tool. Do not perform makeshift repairs. (Use parts list provided to inspection. • Consult manual for specific maintaining and adjusting
procedures. • Keep tool lubricated and clean for which it comes to contain long hair. • Wear...
Operation Manual - Page 3
... securely so that sleeve will have completely read and understood this manual to the instructions.
Unpacking Sander
ASSEMBLY
Refer to Figures 3 and 4, pages 3 and 4. To install sander: • The sander must be installed on a workbench or a tool stand (see Recommended Accessories, page 9) using the tool.
• Sander can be enough room that it is being used. Base Dimension...
Operation Manual - Page 4
... terminals be securely connected to the motor is controlled by an authorized service facility.
• Green (or green and yellow) conductor in use . If repair or replacement of plug when installing or removing from electrical shock.
• Check with a qualified electrician if grounding instructions are not understood or if in accordance with a properly grounded 3-prong...
Operation Manual - Page 5
... be securely fastened. • Make sure all moving parts are properly attached. OPERATION
Refer to 50 ft 16 NOTE: Using extension cords over 50 ft.
DESCRIPTION The Craftsman Oscillating Spindle Sander makes sanding irregular shapes and curves in foreign objects being thrown into the abrasive. • Always support workpiece with table. • Never push a sharp corner...
Operation Manual - Page 6
... the switch to remove scratches left by a qualified service technician. The switch cannot be locked from unauthorized use of the sander.
NOTE: Should the key be removed from oscillating completely, causing damage to accumulate on switch until it is worn, cut, or damaged in this tool are permanently lubricated at your workpiece. In general...
Operation Manual - Page 7
... Applying too much pressure to develop full 1. Tighten spindle knob Replace sandpaper
1. Contact Sears Service Center
if necessary Adjust motor and spindle alignment
MAINTENANCE
7 Short circuit in motor or loose connections
2. Low voltage 2. Install correct fuses or circuit breakers
1. Remove sawdust with sawdust
Spindle does NOT travel completely through 1″ stroke...
Operation Manual - Page 9
...Seal
1
6003ZZ Ball Bearing*
1
Bearing Retainer
1
Spindle
1
5-0.8mm Fiber Hex Nut*
1
Bushing (set of 2)
1
5-0.8 x 40mm Socket Head Bolt*... 25759.00
DESCRIPTION
QTY. REPLACEMENT PARTS LIST FOR SANDER
KEY NO.
1 2
...
2
6-1.0 x 12mm Socket Head Bolt* 7
Base
1
Switch
1
Capacitor
1
Operator's Manual
1
Recommended Accessories Δ ¾″ Abrasive Sleeves, 3 pc. (50, 80,...
Operation Manual - Page 12
... or ours! in items like garage door openers and water heaters.
1-800-4-MY-HOME® (1-800-469-4663)
Call anytime, day or night (U.S.A.
Get it -yourself. For Sears professional installation of home appliances and items like vacuums, lawn equipment, and electronics, call anytime for the location of your nearest
Sears Parts & Repair Service Center
1-800-488-1222 (U.S.A.)
www...
Craftsman 21500 Reviews
We have not received any reviews for Craftsman yet.