Craftsman 21513 - 2 x 42 in. Belt/6 Disc Sander Support and Manuals
Get Help and Manuals for this Craftsman item
View All Support Options Below
Free Craftsman 21513 manuals!
Problems with Craftsman 21513?
Ask a Question
Free Craftsman 21513 manuals!
Problems with Craftsman 21513?
Ask a Question
Most Recent Craftsman 21513 Questions
How Much Did This Cost New
(Posted by Anonymous-54214 12 years ago)
Craftsman 21513
will buy 21513 soon andhave a question - is it possible to take the platen off to getslack on the be...
will buy 21513 soon andhave a question - is it possible to take the platen off to getslack on the be...
(Posted by bountymutiny1789 13 years ago)
Popular Craftsman 21513 Manual Pages
Operation Manual - Page 1
Operator's Manual
I
x 42" Belt
SANDER
Model No. 351.215130
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
www.sears.com/craftsman
20067.01 Draft (11/07/03)
Operation Manual - Page 2
...
WARNING: For your nearest Sears Service Center (1-800-4-MY-HOME) to arrange for product repair, or return this productto place of purchase for job. BE PREPARED FOR JOB
• Wear proper apparel. Never operate power tools when tired, intoxicated or when taking medications that is damaged should be properly repaired or replaced. Do not expose...
Operation Manual - Page 3
... between belt table and belt is being used. WARNING; Use of improper accessories may cause risk of injury to Figures 2 and 3. AluminumDisc withAbrasive
Refer to order replacement parts. Use operator's manual to Figure 1. Serious injury could occur if tool is pasted evenly on the aluminum disc.
• Replace dust chute ATTACH DISC TABLE
Refer to Figure 2, • Set the disc...
Operation Manual - Page 4
...accordance with National Electric Code and local codes and ordinances. WARNING: This work should be replaced with a properly grounded 3-prong
receptacle installed in doubt as ...sander with Adapter
• DO not use .
Running the unit on the rear side of plug when installingor removing from electrical shock. • Check with a qualified electrician if grounding
instructions...
Operation Manual - Page 5
... and sanding wood, plastic and metal. l-Black ,)
(_ 4-Yellow )
3- DESCRIPTION
Craftsman 2 x 6" Belt and Disc Sander has a 2" x 42"
belt and 6" disc for contour sanding.
Always wear safety goggles complying with motor and wiring installed as shown in Figure 6. CAUTION: Always observe following specifications:
Horsepower (Maximum Developed
2/3
Voltage
120/240
Amps Hertz...
Operation Manual - Page 6
... move workpiece across abrasive to prevent heat buitt up to set belt table at the desired angle, and secure it is recommended to mount the sander onto a stand (see "Recommended Accessories", page 13) or to Figure 9, page 7.
• Test the tracking. NOTE: There may be replaced when worn, torn, or glazed.
• Loosen and remove...
Operation Manual - Page 7
... wood to Figure 7. WARNING: Disconnect sander from abrasive belt. If belt moves to secure bolt position. The 2" belt size is used to Figures 7 and 10. • Belt platen can be used to
remove belt cover.
• Loosen socket head bolts and adjust belt platen position.
• Tighten bolts and secure platen. • Replace belt cover and tighten knobs. Figure...
Operation Manual - Page 8
... available (see Recommended Accessories, page 13). • Replace disc table and tighten knobs. Keep end butted against work stop at desired angle, lock it easier to feed the work while finishing. • Do not apply wax to clean painted parts, rubber parts and plastic guards.
Remove belt table.
• Mount work stop for securing work and...
Operation Manual - Page 9
... parts
list to repair motor may create a hazard unless repair is done by a qualified service technician. KEEP TOOL IN REPAIR • If power cord is available at your nearest Sears store.
9 Repair service is worn, cut, or damaged in any way,
have it replaced immediately. • Replace worn abrasives when needed. • Replace any damaged or missing parts. Any attempt to order parts...
Operation Manual - Page 10
...)
3. Correct the low line voltage conditions 3. Replace belt Ease up on motor
5. Defective switch
1. Incorrect fuses or circuit breakers
4. Replace capacitor 1. Reduce the load on wires
3. Defective belt 1. Install correct fuses or circuit breakers
in motor or loose
connections
2. Belt housing not set properly
5. Request a voltage check from the power...
Operation Manual - Page 13
.... 67-72)
5-0.8 x 12mm Pan Head Screw*
2
Pointer
1
1 x 42" Abrasive Belt
1
Parts Bag
1
Operator's Manual
1
Recommended Accessories Abrasive Belts 2 x 42" (Fine) Abrasive Belts 2 x 42" (Medium)
t_ Abrasive Belts 2 x 42" (Coarse) Abrasive Disc 6" (Assorted) Abrasive Belts 1 x 42" (Fine) Abrasive Belts 1 x 42" (Medium)
t, Abrasive Belts 1 x 42" (Course) t_ Abrasive Cleaner
9-28480 9-28481...
Operation Manual - Page 24
... made it, no matter who sold itI
For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. Registered Trademark/ TM Trademark/ SMService Mark of home appliances and items like vacuums, lawn equipment, and electronics, call or go on a product serviced by Sears:
1-800-827-6655 (U.S.A.)
lm800"361--6665 (Canada)
i
Para...
Craftsman 21513 Reviews
We have not received any reviews for Craftsman yet.