Craftsman 21513 Support Question
Craftsman 21513 Support Question
Find answers below for this question about Craftsman 21513 - 2 x 42 in. Belt/6 Disc Sander.Need a Craftsman 21513 manual? We have 1 online manual for this item!
Question posted by bountymutiny1789 on May 20th, 2010
Craftsman 21513
will buy 21513 soon and have a question - is it possible to take the platen off to get slack on the belt to be able to sand something egg-shaped? (precision is not required on the egg-shaped item) thanks, Donald
Current Answers
Related Craftsman 21513 Manual Pages
Operation Manual - Page 1
Operator's Manual
I
x 42" Belt
SANDER
Model No. 351.215130
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com/craftsman
20067.01 Draft (11/07/03)
Operation Manual - Page 2
...rental purposes, this warranty will apply for which it was not designed.
• Disconnect tool when changing belt or abrasive disc. • Avoid accidental start-up. Warrant.y SafetyRules Unpackin.g Assembly Installatio..n
Operation Maintenanc..e...away from moving parts and sanding
surfaces.
• Never leave tool running unattended. BE PREPARED FOR JOB
• Wear proper apparel.
Operation Manual - Page 3
... should be filed with miter gauge, belt platen, work table.
• Maintain '/_6"maximum clearance between table and sanding belt or disc. Use of improper accessories may cause risk of dust chute using 4-0,7 x 8mm socket head bolt from the hardware bag. • Set the belt table at all times when tool is _/_6o"r less.
• Attach pointer...
Operation Manual - Page 4
... repair or replacement of electrical shock.
Heavy loads require that is equipped with an approved 3--conductor cord ... provides a path of belt housing. • Tighten hex nut. If it is controlled by a qualified electrician.
• Inspect tool cords periodically, and if... motor burnout. POWER SOURCE WARNING: Do not connect sander to determine the minimum wire size (A.W.G.) extension cord...
Operation Manual - Page 5
... is not recommended. Refer to prevent unauthorized use the sander with motor and wiring installed as shown in Figure 6.
Disc guard has 1'/2" dust collection chute.
Motor and wires are properly attached. DESCRIPTION
Craftsman 2 x 6" Belt and Disc Sander has a 2" x 42"
belt and 6" disc for angle sanding. The power lines are inserted directly onto the switch. long is assembled...
Operation Manual - Page 6
.... BELT
WARNING: Disconnect sander from power source before making any adjustments. • To adjust belt table angle, loosen the socket head
bolt and adjust table to ensure that the splice in the direction of abrasive belt, disc and all moving parts.
• For optimum performance, do not stall motor or reduce speed. Adjustments
'm_-Belt Platen ,_p...
Operation Manual - Page 7
... an auxiliary piece of wood. • Using a C-clamp, attach auxiliary piece of the bolt with the table. sting Bolt
Locking
Move the workpiece against belt. WARNING: Disconnect sander from power source before making any adjustments, The platen is convenient for sanding curved surfaces. WARNING: Disconnect sander from abrasive belt. Use belt sander to properly support the workpiece when...
Operation Manual - Page 8
... belt.
• Move the workpiece across the down on the tool. minum disc. WARNING: After sanding wood or nonmetallic material, always clean area of the miter gauge. They require no...the abrasive disc.
Keep end butted against work and holding belt table on sander.
Loosen screw and reposition indicator if necessary. Remove belt table.
• Mount work stop to sander using the...
Operation Manual - Page 9
... missing parts. Any attempt to order parts. Use parts
list to repair motor may create a hazard unless repair is done by a qualified service technician. KEEP TOOL IN REPAIR • If power cord is available at your nearest Sears store.
9
Operation Manual - Page 10
...1. Rewire motor as per wiring diagram, see Operation
section, "Horizontal Belt Sanding"
10 Defective belt 1. Short circuit in motor for loose or
shorted terminals or worn insulation... line voltage 4. Inspect connections in motor or loose
connections
2. Belt housing not set properly
5. SYMPTOM
POSSIBLE CAUSE(S)
CORRECTIVE ACTION
Motor will not start
1. Defective switch
1....
Operation Manual - Page 13
.... 67-72)
5-0.8 x 12mm Pan Head Screw*
2
Pointer
1
1 x 42" Abrasive Belt
1
Parts Bag
1
Operator's Manual
1
Recommended Accessories Abrasive Belts 2 x 42" (Fine) Abrasive Belts 2 x 42" (Medium)
t_ Abrasive Belts 2 x 42" (Coarse) Abrasive Disc 6" (Assorted) Abrasive Belts 1 x 42" (Fine) Abrasive Belts 1 x 42" (Medium)
t, Abrasive Belts 1 x 42" (Course) t_ Abrasive Cleaner
9-28480 9-28481...
Operation Manual - Page 24
... or maintenance agreement (Canada) on -line for the location of your home-of home appliances and items like vacuums, lawn equipment, and electronics, call or go on a product serviced by Sears:
1-800...888-784-6427)
www.sears.ca ;i _
....S_EAR, iiiii!i!_ii_ii!
Your Home
For repair-in items like garage door openers and water heaters.
1-800-4-MY-HOME ® (1-800-469-4663)
Call ...
Similar Questions
Is This Sander Still Available For Purchase?
(Posted by pkrusac 10 years ago)
How Much Did This Cost New
(Posted by Anonymous-54214 12 years ago)
Belt Only Contacts Surface To Be Sanded Along One Edge.
My sander is brand-new (out lof the box). The belt installation was a piece of cake and adjusting th...
My sander is brand-new (out lof the box). The belt installation was a piece of cake and adjusting th...
(Posted by scorpio1155 12 years ago)
Belt Change
How do I change the belt on my sander? Model 531.215140 Thanks
How do I change the belt on my sander? Model 531.215140 Thanks
(Posted by rmuskat 13 years ago)