Craftsman 21514 Support Question
Craftsman 21514 Support Question
Find answers below for this question about Craftsman 21514 - Belt & Disc Sander.Need a Craftsman 21514 manual? We have 1 online manual for this item!
Question posted by DamSurveyr on February 19th, 2012
Belt Sander Froze Up, Replaced Belt, Now It Runs Backwards
Above
Current Answers
Related Craftsman 21514 Manual Pages
Operation Manual - Page 1
Sears, Roebuck and Co., Hoffman
www.sears.com/craftsman
30657.00 Draft (04/07/09)
Estates, IL 60179 U.S.A.
Operator's Manual
CRRFISMRN °
4 x 36" Belt 6" Disc
SANDER Model No.
351.215141
CAUTION: Read and follow
all Safety Rules and Operating Instructions before First Use
of this manual with tool. Keep this Product.
Operation Manual - Page 2
...tool when changing belt or abrasive disc. • Avoid accidental start-up. Always wear OSHA/NIOSH approved, properly fitting face mask or respirator when using such tools... (or replacement if repair proves impossible).
Do not force tool or attachment to do not leave tool until it... surfaces.
• Never leave tool running unattended.
Do not expose power tools to rain.
° Work area ...
Operation Manual - Page 3
...
Immediately report missing parts to Figures 2 - 6.
piece.
TOOLS NEEDED While assembling or adjusting your belt and disc sander, you have to Figure 1. Check for shipping damage. A Sander B Miter Gauge Assembly C Back Stop D Table E Stud F Handle with carrier. To install sander: • The sander must be bolted to mount the sander. WARNING: Do not operate machine until you...
Operation Manual - Page 4
....
• This tool is controlled by a single pole
locking rocker switch. GROUNDING INSTRUCTIONS
WARNING: Improper connection of least resistance for electrical shock.
4 Equipment should be plugged directly into disc guard. ° Using a combination square, set the table perpendicular to
the belt and secure in position. Using Table with both the disc and belt. Heavy loads...
Operation Manual - Page 5
....
° Inspect tool cords periodically, and ...replace it must be replaced with a properly grounded 3-prong receptacle installed in accordance with approved, 3-conductor cord to be used at a desired angle while sanding. Sander has a 2" dust port that is used on the work should be tested by a qualified electrician. SPECIFICATIONS Belt size
Belt platen area Belt speed Disc diameter Disc...
Operation Manual - Page 6
...your hands clear of abrasive belt, disc and all fasteners are properly attached. Sanding belt assembly can be adjusted from vertical to Figure 11, page 7.
Abrasive backing may tear.
° Replace abrasives when they become ... of any parts on the tool, turn switch OFF and remove the plug from power source.
° Recheck table handle and bolts.
To turn the sander ON, pull the switch to...
Operation Manual - Page 7
... well suited for beveled work evenly across down side (left) of sander.
Loosen screw and reposition Pointer if necessary. • After setting miter gauge square to belt (disc), adjust to desired position. ABRASIVE DISC SANDING
• Abrasive disc sanding is located on belt side of abrasive disc. Pointer should be at outer edge.
• For accuracy, use...
Operation Manual - Page 8
... or missing parts. They require no further lubrication.
• When operation seems stiff, a light coat of belt travel to Figure 15. • Sanding belt should point in this tool are available (See Recommended Accessories, page 13).
• Replace disc cover. Use parts list to clean painted parts, rubber parts and plastic guards. Setting Miter Gauge...
Operation Manual - Page 9
...power (power output of motor decreases rapidly with lights, appliances and other motors
2. Replace switch 4. Install correct fuses or circuit breakers
1. Increase wire sizes, or reduce ...2. Power line overloaded with decrease in power line
Motor fails to workpiece
Abrasive belt runs off top Not tracking properly wheel
CORRECTIVE ACTION 1. Incorrect fuses or circuit breakers ...
Operation Manual - Page 10
Replacement Parts Illustration for Belt Housing
11
,..b
o
35 34
37 36
20 16
\ 39 Model 351.2151 41
Figure 17 -
Operation Manual - Page 11
...Pan Head Screw*
Back Stop 6mm Flat Washer* 6mm Lock Washer* 6-1.0x15mm Socket Head Bolt Drive Drum 8-1.25 x 10mm Set Screw Abrasive belt
Ball Bearing 6000ZZ* Bearing Plate Idler Assembly Spring Tension Lever 6-1.0 x 20mm Socket Head Bolt* Stud
QTY. 1 2 1 1 1 ...Cover 5-0.8 x 15mm Socket Head Bolt 5-0.8 x 8mm Flat Head Bolt Belt Cover Base Plate Drive Shaft Base Cover
Horizontal Stop 8-1.0mm Hex Nut*...
Operation Manual - Page 12
Model 351.21 5141
Figure 18 - Replacement Parts Illustration for Motor and Disc
8
,,,,,.L
1
44
Operation Manual - Page 13
...00 Capacitor 1 49 23744.00 MountinBgracke(St etof4) 1 50 23704.00 Gasket
1 A 30657.00 OperatorM'sanual 1
Recommended Accessories A Abrasive Belts 4 x 36" (Fine) 120 Grit A Abrasive Belts 4 x 36" (Medium) 80 Grit A Abrasive Belt 4 x 36" (Coarse) 50 Grit A Abrasive Disc 6" Assorted Grit A Abrasive Cleaner
QTY. 2 4 1 1 1 1 2 2 1 1 1 6 6 1 1 1 1 1 2 2 2 1 1 1
9-28394 9-28395 9-28396 9-28973 9-28000...
Operation Manual - Page 24
For the replacement parts, accessories and owner's manuals that you need to do-it !
For Sears professional installation of home appliances and items like vacuums, lawn equipment, and ...
Similar Questions
Or91721 Replacement Belt
What is a replacement belt that can purchased with out a month relay from order from Sears Parts?
What is a replacement belt that can purchased with out a month relay from order from Sears Parts?
(Posted by Spauldid51 10 years ago)
Can I Get Replacement Belts (2 Each) For My Craftsman 152.211740 Utility Sharpen
I have tried unsuccessfully including with Sears to get the two replacement belts for my Craftsman U...
I have tried unsuccessfully including with Sears to get the two replacement belts for my Craftsman U...
(Posted by Kappynric 11 years ago)
How Much Did This Cost New
(Posted by Anonymous-54214 12 years ago)
Parts
Where can I buy a second table for the 21524 belt/disk sander. Part number 23655.00 Dan Mazel Bill...
Where can I buy a second table for the 21524 belt/disk sander. Part number 23655.00 Dan Mazel Bill...
(Posted by ss90680 12 years ago)
Belt Change
How do I change the belt on my sander? Model 531.215140 Thanks
How do I change the belt on my sander? Model 531.215140 Thanks
(Posted by rmuskat 12 years ago)