Craftsman 21514 Support Question
Craftsman 21514 Support Question
Find answers below for this question about Craftsman 21514 - Belt & Disc Sander.Need a Craftsman 21514 manual? We have 1 online manual for this item!
Question posted by ss90680 on February 4th, 2012
Parts
Where can I buy a second table for the 21524 belt/disk sander. Part number 23655.00
Dan Mazel
Billings MT 59106
406/656-6326
Current Answers
Related Craftsman 21514 Manual Pages
Operation Manual - Page 1
Sears, Roebuck and Co., Hoffman
www.sears.com/craftsman
30657.00 Draft (04/07/09)
Estates, IL 60179 U.S.A. Keep this Product. Operator's Manual
CRRFISMRN °
4 x 36" Belt 6" Disc
SANDER Model No.
351.215141
CAUTION: Read and follow
all Safety Rules and Operating Instructions before First Use
of this manual with tool.
Operation Manual - Page 2
... other jewelry which it was not designed.
• Disconnect tool when changing belt or abrasive disc. • Avoid accidental start-up. Do not perform makeshift repairs. (Use parts list provided to order replacement parts.)
KNOW HOW TO USE TOOL
• Use right tool for safest operation. • Remove adjusting tools. Keep proper footing and balance. • Never stand...
Operation Manual - Page 3
...a foot onto each corner of the base of the abrasive disc.
3 Additional parts which need the following tools: • 13mm Wrench • 3 and 5mm Hex ...tool is completely assembled according to sander, should be installed in the work - piece. TOOLS NEEDED While assembling or adjusting your belt and disc sander, you have to stand in line with miter gauge, belt platen or work table...
Operation Manual - Page 4
... assembly steps have been completed. POWER SOURCE
WARNING: Do not connect sander to Figures 7, 8 and 9, pages 4 and 5. Using Table with both the disc and belt. If necessary, set the table perpendicular to
the belt and secure in position.
• Center the abrasive disc onto the aluminum disc and press on voltages which are not understood or if in...
Operation Manual - Page 5
...Belt and Disc Sander is encountered, it is not recommended. The belt housing can be used to sand, deburr, bevel and grind large workpieces of wood and plastic.
The power lines are used to properly protect against electrical shock.
SPECIFICATIONS Belt size
Belt platen area Belt speed Disc diameter Disc speed Table dimensions Table...° Inspect tool cords periodically, ...
Operation Manual - Page 6
... with the directional arrows.
° Keep your hands clear of abrasive belt, disc and all moving parts are free and clear of any interference.
° Make sure all moving parts.
° For optimum performance, do not stall motor or reduce speed.
The sander can be turned on the upper front right of the base. To...
Operation Manual - Page 7
Back stop supports the workpiece when sanding on the belt with the belt assembly in the horizontal position. • Remove table and stud from belt assembly. • Tilt belt assembly from vertical to horizontal position and
secure in a vertical position. Apply only enough pressure to allow abrasive belt to
belt (disc).
NOTE: The horizontal limit stop is more material...
Operation Manual - Page 8
... by loosening and removing four screws. See "Adjusting Belt Tracking", page 6. • Assemble in this tool are available (See Recommended Accessories, page 13).
• Replace disc cover.
Select the desired abrasive disc and apply to Figure 16. • Remove table assembly. • Remove disc cover by pushing tension lever toward idler
drum.
Figure 15 - REPLACING ABRASIVE...
Operation Manual - Page 9
..., appliances and other motors
2. Reduce the load on pressure
See operation "Adjusting Belt Tracking"
9 Correct the low line voltage conditions 3. Install correct fuses or circuit...switch 4. Incorrect fuses or circuit breakers in power line
Motor fails to workpiece
Abrasive belt runs off top Not tracking properly wheel
CORRECTIVE ACTION 1. Replace switch 4. General ...
Operation Manual - Page 10
Model 351.2151 41
Figure 17 - Replacement Parts Illustration for Belt Housing
11
,..b
o
35 34
37 36
20 16
\ 39
Operation Manual - Page 11
... belt
Ball Bearing 6000ZZ* Bearing Plate Idler Assembly Spring Tension Lever 6-1.0 x 20mm Socket Head Bolt* Stud
QTY. 1 2 1 1 1 1 1 1 2 2 2 1 3 1 1 1 1 1 1 1 1
PART NO.
1 23682.00 2 23683.00 3 08685.00 4 STD870510 5 STD851005 6 23684.00 7 05374.00 8 01833.00 9 23685.00 10 N/A 11 23681.00 12 N/A 13 23689.00 14 STD840812 15 23690.00 16 18365.00 17 STD315525 18 23691.00 19 STD870525 20 03835.00...
Operation Manual - Page 12
Model 351.21 5141
Figure 18 - Replacement Parts Illustration for Motor and Disc
8
,,,,,.L
1
44
Operation Manual - Page 13
... Belts 4 x 36" (Medium) 80 Grit A Abrasive Belt 4 x 36" (Coarse) 50 Grit A Abrasive Disc 6" Assorted Grit A Abrasive Cleaner
QTY. 2 4 1 1 1 1 2 2 1 1 1 6 6 1 1 1 1 1 2 2 2 1 1 1
9-28394 9-28395 9-28396 9-28973 9-28000 NO. KEY NO. PARTNO. KEY QTY. A Notshown. DESCRIPTION 1 23652.00 MiteGr augeAssembly 2 23653.00 Knob 3 23654.00 LockinHg andle 4 STD8510066ramFlatWasher*
5 23655.00 Table...
Operation Manual - Page 24
..., LLC
MC Marque de commerce / MD Marque d6posee de Sears Brands, LLC
© Sears Brands, LLC in your nearest
Sears Parts & Repair Service Center
1-800-488-1222 (U.S.A.) 1-800-469-4663 (Canada)
www.sears.com
www.sears.ca
To purchase a protection...,
no matter who made it, no matter who sold it -yourself. For the replacement parts, accessories and owner's manuals that you need to do-it !
Similar Questions
Replacement Part
I have an older craftsman garage door opener. The wall push button does not work and the part is not...
I have an older craftsman garage door opener. The wall push button does not work and the part is not...
(Posted by hleblanc 8 years ago)
Are All Parts Available For The 21500?
The Sears 351 215000 Drum Sander is not available anymore. Are all of the parts available?
The Sears 351 215000 Drum Sander is not available anymore. Are all of the parts available?
(Posted by sherm54806 9 years ago)
How Much Did This Cost New
(Posted by Anonymous-54214 12 years ago)
Belt Change
How do I change the belt on my sander? Model 531.215140 Thanks
How do I change the belt on my sander? Model 531.215140 Thanks
(Posted by rmuskat 12 years ago)