Craftsman 21500 Support Question
Craftsman 21500 Support Question
Find answers below for this question about Craftsman 21500 - Oscillating Spindle Sander.Need a Craftsman 21500 manual? We have 1 online manual for this item!
Question posted by z2abrown on June 14th, 2011
Craftsman Lt 1500
my craftsman lt 1500 will start but will not move forward in drive or vice versa
Current Answers
Related Craftsman 21500 Manual Pages
Operation Manual - Page 1
SAFETY
ASSEMBLY
OPERATION
MAINTENANCE
Operator's Manual
Oscillating Spindle
SANDER Model No.
351.215000
CAUTION: Read and follow
all Safety Rules and Operating Instructions before First Use of this manual with tool. Keep this Product. www.sears.com/craftsman
25759.00 Draft (01/22/08)
PARTS LIST
ESPAÑOL
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Operation Manual - Page 2
... Check for which it was not designed. • Disconnect tool when changing sanding drum. • Avoid accidental start-up. Make workshop childproof. Check to determine that the
guard ...Troubleshooting 7 Parts Illustration and List 8-9 Español 12-19
WARRANTY
ONE-YEAR FULL WARRANTY ON CRAFTSMAN TOOL If this manual even if you may cause risk of injury to persons. • Handle the ...
Operation Manual - Page 3
...; ABRASIVE SLEEVE: • Place the ½″ table insert over spindle and onto the table.
SAFETY
ASSEMBLY
• Turn machine off if it jams.
• Support workpiece with the wood while using the tool.
• Sander can be installed on a workbench or a tool stand (see Recommended Accessories, page 9) using bolts, lock washers and hex...
Operation Manual - Page 4
... that is encountered, it must be tested by a qualified electrician.
• Inspect tool cords periodically, and if damaged, have been completed.
To ensure proper ground, grounding means...be replaced with National Electric Code and local codes and ordinances. POWER SOURCE WARNING: Do not connect sander to Figures 6, 7 and 8, pages 4 and 5. Normal loads will not fit in accordance ...
Operation Manual - Page 5
... rapidly against electrical shock. Motor and wires are available at 120 volts. DESCRIPTION The Craftsman Oscillating Spindle Sander makes sanding irregular shapes and curves in wiring schematic (See Figure 8). SAFETY PRECAUTIONS ...Safety goggles are installed as shown in wood easy and convenient.
Make sure tool is inspected. To turn
switch OFF and remove the plug from power ...
Operation Manual - Page 6
... is located beneath the work table on the tool. The shielded ball bearings in any way,... the switch. For best results, start with each grit until the surface ...Craftsman wet/dry vacuums.
The use by the coarser grit and finer grit used to repair motor may prevent the spindle...Turn the switch to OFF position and disconnect sander from oscillating completely, causing damage to the worm gear ...
Operation Manual - Page 7
Defective capacitor
Motor will not start ; Undersize wires or circuits too long
with vacuum 2. Incorrect fuses or circuit breakers in voltage at 3. Damaged or loose oscillating
mechanism
Excessive noise Note: Normally operating sander does make some noise
Spindle and motor not aligned properly
CORRECTIVE ACTION 1. Inspect line cord or plug for proper voltage 2. Inspect...
Operation Manual - Page 9
REPLACEMENT PARTS LIST FOR SANDER
KEY NO.
1 2
3
4
5
6 7 8 9 10 11 12 13 14 15 16...5-0.8 x 10mm Flat Head Screw 3
Fan Housing
1
5mm Flat Washer*
6
5-0.8 x 12mm Socket Head Bolt* 6
Seal
1
6003ZZ Ball Bearing*
1
Bearing Retainer
1
Spindle
1
5-0.8mm Fiber Hex Nut*
1
Bushing (set of 2)
1
5-0.8 x 40mm Socket Head Bolt* 1
3AMI-17 Retaining Ring
1
Collar
1
8mm Wavy Washer
3
...
Similar Questions
Left Blade On My Craftsman Lt 2000 18.5 Horsepower Mower Came Loose I Retightene
the left blade on my craftsman 2000 lt mower came loose i retightened it as soon as i turned it on i...
the left blade on my craftsman 2000 lt mower came loose i retightened it as soon as i turned it on i...
(Posted by elbert64jw 8 years ago)
Is There A Manuel For A Craftsman Lt 2000 18 Hp Ohv Intel Engine?
(Posted by eaharlan 8 years ago)
Are All Parts Available For The 21500?
The Sears 351 215000 Drum Sander is not available anymore. Are all of the parts available?
The Sears 351 215000 Drum Sander is not available anymore. Are all of the parts available?
(Posted by sherm54806 9 years ago)
Miles?
i have a lts 1500 craftsman riding lawn mower, how many miles does it get to the gallon
i have a lts 1500 craftsman riding lawn mower, how many miles does it get to the gallon
(Posted by alyssamalcolm 11 years ago)
I Have A Lt 1500 And Need To Obtain A Diagram Of The Carb And Throttle
(Posted by tjsullivan51 12 years ago)