ZyXEL MM-7201 Support and Manuals
Get Help and Manuals for this ZyXEL item
View All Support Options Below
Free ZyXEL MM-7201 manuals!
Problems with ZyXEL MM-7201?
Ask a Question
Free ZyXEL MM-7201 manuals!
Problems with ZyXEL MM-7201?
Ask a Question
Popular ZyXEL MM-7201 Manual Pages
User Guide - Page 3
... Audience
This manual is recommended you ! You should have at least a basic knowledge of individual screens and supplementary information.
• Supporting Disc Refer to the included CD for support documents.
• ZyXEL Web Site Please refer to www.zyxel.com for people who want to configure the MM-7201. Related Documentation
• MS-7206 Hardware Installation Guide Hardware guide for...
User Guide - Page 26
... of the MM7201 using fiber.
• Router D provides secure Internet access for firmware upgrades and configuration backup/restore. The MS-7206 system is recommended for troubleshooting by service engineers. Restoring an earlier working configuration may be monitored by an SNMP manager. If you would not have to reset the MM-7201 to its factory default settings. Line commands...
User Guide - Page 32
...port has input pins and output pins. Figure 4 ALARM Pins Layout
Pin 1
Pin 5
Pin 9
Pin 6
32
MS-7206 User's Guide To signal an alarm, the MM-7201 opens the circuit for pins 1 and 6 (the common pin) and closes the circuit for example, the voltage or temperature is outside ...control
Connect the male 9-pin end of the console cable to a serial port (COM1, COM2 or other COM port) of the MM7201.
User Guide - Page 77
To open this screen to control the power to the each slot or to change what type of card is in the slot without restarting the system.
CHAPTER 11
Slot Setup
11.1 Slot Setup
Use this screen, click Basic Setting > Slot Setup. Figure 23 Slot Setup
MS-7206 User's Guide
77
User Guide - Page 122
...disabled when more than one port forms a loop in the MST instance.
122
MS-7206 User's Guide
Enter the end of the VLAN ID range that you make them. to the MST instance.
•...a switch. Ports with a higher priority numeric value are mapped to set the common settings and then make some settings the same for the specific spanning tree instance. Path cost is 128. The slower the media...
User Guide - Page 175
... 802.1Q tag in the Port Setup screen.
• "0" is the lowest priority level and "7" is a standard Ethernet type code identifying the frame and indicates that whether the frame carries IEEE 802.1Q tag information.
MS-7206 User's Guide
175 Many vendors use 0x8100 or 0x9100.
SP TPID (Service Provider Tag Protocol Identifier) is...
User Guide - Page 187
... allows the multicast devices to update the multicast forwarding table to forward or not forward multicast traffic to the other multicast groups are managed by IGMP snooping.
In this case, you must manually configure the forwarding settings on the switch that matches the... a receiver port can connect through a port configured as the receiver on the switch, an
MS-7206 User's Guide
187
User Guide - Page 196
... the authentication priority, activate authorization and accounting settings.
196
MS-7206 User's Guide However, there is able to the memory capacity of users from a central location.
Table 60 RADIUS vs TACACS+
RADIUS
Transport Protocol
UDP (User Datagram Protocol)
Encryption
Encrypts the password sent for authentication.
Figure 84 AAA Server
Client
AAA Server
28...
User Guide - Page 197
... panel to display the screen as shown.
Figure 86 RADIUS Server Setup
MS-7206 User's Guide
197 Chapter 28 AAA Click Advanced Application > AAA in the AAA screen to view the screen as shown. Click on RADIUS servers. Figure 85 AAA
28.2.1 RADIUS Server Setup
Use this screen to configure your RADIUS server settings.
User Guide - Page 199
...changes to the nonvolatile memory when you click Apply.
Figure 87 TACACS+ Server Setup
MS-7206 User's Guide
199 This key is deleted when you are done configuring.
The switch loses these...save your TACACS+ server settings. Chapter 28 AAA
Table 61 RADIUS Server Setup (continued)
LABEL
DESCRIPTION
Shared Secret
Specify a password (up to 32 alphanumeric characters) as shown.
User Guide - Page 201
... changes to the switch's run-time memory. Figure 88 AAA Setup
MS-7206 User's Guide
201 This entry is not sent over the network. The switch...password (up to 32 alphanumeric characters) as shown. This key must be shared between the external TACACS+ accounting server and the switch. Delete
Check this screen to configure authentication, authorization and accounting settings on the AAA Setup...
User Guide - Page 273
...Guide
273 The DHCP Relay Agent Information feature adds an Agent Information field to . Relay Agent Information can change the System Name in Basic Settings > General Setup.
Information
(up to 64 bytes) This optional, read-only field is set according to RFC 3046 for stand-alone switches.
Please refer to system name set...value is in Basic Settings > General Setup. You can include...
User Guide - Page 276
... management IP addresses for VLANs.
Figure 133 DHCP VLAN Setting
276
MS-7206 User's Guide Click IP Application > DHCP in the navigation panel, then click the VLAN link In the DHCP Status screen that you want to configure DHCP settings for on the switch.
See Section 10.1 on the VLAN domain of the...
User Guide - Page 279
Figure 135 DHCP VLAN Setting Example
MS-7206 User's Guide
279 Chapter 37 DHCP
In the DHCP VLAN Setting screen, set the DHCP Status to Server and configure two DHCP client IP address pools for the two networks.
The following shows an example.
User Guide - Page 360
... on the MM-7201.
Make a copy of the MM-7201's configuration and put it is the grouping of physical ports into one another. Firmware Upgrade
Download new firmware (when available) from the ZyXEL web site and use multiple lower-speed links than to under-utilize a high-speed, but more costly, single-port link.
Chapter 50 Product Specifications
Table 129...
ZyXEL MM-7201 Reviews
We have not received any reviews for ZyXEL yet.