Weider 8150 Support and Manuals
Get Help and Manuals for this Weider item
Popular Weider 8150 Manual Pages
Instruction Manual - Page 1
... provide the following information when ordering replacement parts:
• the MODEL NUMBER of the product (WEEVSY49220)
• the NAME of the product (WEIDER® 9150 weight system)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING in...
Instruction Manual - Page 2
... CHART 18 TROUBLESHOOTING AND MAINTENANCE 19 CABLE DIAGRAMS 20 EXERCISE GUIDELINES 21 ORDERING REPLACEMENT PARTS Back Cover
Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the centre of this manual. MONDAY
Date: / /
EXERCISE
TUESDAY
Date: / /
AEROBIC EXERCISE
WEDNESDAY
Date: / /
EXERCISE
WEIGHT
SETS
REPS
WEIGHT
SETS
REPS
WEIDER is a registered...
Instruction Manual - Page 3
... exercise a regular and enjoyable part of your workouts. Cover the floor or carpet beneath the weight system to support a maximum user weight of 136 kg (300 lbs.).
10. Make sure that could cause the weight system to order a free replacement decal. If the decal is missing or illegible, please call our Customer Service Department toll-free at...
Instruction Manual - Page 4
...sets of the body. A "set" is an individual matter. Rest for selecting the versatile WEIDER® 9150 weight system.
BEFORE YOU BEGIN
Thank you for 3 minutes after each set.
Once you will help us assist you feeling exhausted. On the exercise guide accompanying this manual... of weight training and aerobic exercise will leave you , please note the product model number...
Instruction Manual - Page 5
... possible, we have questions after reading the assembly instructions, please call our Customer Service Department at 0845 089 009. Make sure that the cable traps do otherwise. Place all parts of the weight system in individual bags.
Make sure that there is designed to the weights.
If a part is completed. How to read the information on...
Instruction Manual - Page 6
...REPLACEMENT PARTS on page 5.
Do not tighten the Locknuts yet.
42
21
4 1
86 21
6
TROUBLESHOOTING AND MAINTENANCE
Make sure all parts are smaller than it .
73 Small Holes
21
73
Press a 40mm x 60mm Inner Cap (27) into the Front Upright (42). The weight...set of the Base (4). Do not tighten the
Locknuts yet.
2
2. Press two 40mm x 60mm Outer Caps (73) onto the ends of the weight ...
Instruction Manual - Page 7
...weight guides.
Slide two Weight Bumpers (19) onto the Weight Guides (62). Lubricate the indicated holes in the Weights (25). "Top" refers to the 12.5 lb. Insert the two Weight Guides (62) into the bottom of the Weight Tube (63). Be
sure that the Weight Guides...
63
Pin
72 25
Pin Groove
18
7
Attach the
Weight Guides to the Base and the Stabiliser with
the holes in ...
Instruction Manual - Page 8
... (46). Always remove the Curl Pad (24) when it with two M10 x 60mm Bolts (7), the Support Plate (71), and two M10 Nylon Locknuts (21).
Attach the Press Arm to the Upright with two...the Weight Guides (62).
ATTACHING THE CURL PAD
To attach the Curl Pad (24) to the weight system, the seat frame must be attached to three heights using the different slots in use, and replace ...
Instruction Manual - Page 9
... and a 25mm Cover Cap (65). Replace any worn parts immediately. The weight system can be performed. Turn the bent...11
11. CHANGING THE WEIGHT SETTING
To change the setting of the weight stack, insert the Weight Pin (26) under the desired Weight (25) until the... Right Butterfly Arm (48) as shown in increments of the Weight Guides (62). Do not overtighten the bolts and locknuts that secure...
Instruction Manual - Page 10
...the Pulley Covers
are not properly installed, they may be sure that all parts have been properly tightened. Attach ...that the cables move smoothly, find and correct the problem. see TROUBLESHOOTING AND MAINTENANCE on page 20 for proper cable routing....weight system, pull each cable a few times to the second set of holes from the top of Pulley
Covers (40) to be damaged when heavy weight...
Instruction Manual - Page 11
...Attach the Leg Lever (29) to the Seat Frame (36) with the other end of the Seat (13) to the Weight Tube
(63) with an M10 x 110mm Bolt (64), an M10 Washer (9), and an M10 Nylon Locknut (21).
... in the Leg Lever (29). Slide a Pad Tube (28) into the hole in the Seat Plate (37). the Weight Tube must be able
to the Seat Frame (36) with the M5 x 20mm
13
Self-tapping Screw (80). Locate...
Instruction Manual - Page 13
... Cover Cap (62)
25mm Retainer (68)
Note: Assembly is provided to the key number of the part from the PART LIST in assembly. 40mm x 60mm Inner Cap (27)
50mm Square Inner Cap (44)
This chart ... TO OPEN THE PARTS BAG LABELLED FOR THAT
STAGE. Important: Some parts may have been pre-assembled for each part refers to help you identify the small parts used in the centre of this manual.
Instruction Manual - Page 14
PART IDENTIFICATION CHART-Model No. WEEVSY49220
R0404A
M10 Nylon Locknut (21)
M5 x 20mm Self-tapping Screw (80)
M8 Nylon Locknut (3)
M6 x 16mm Screw (18)
M8 x 45mm Bolt (66) M10 x ...
Instruction Manual - Page 15
... M10 x 115mm Bolt M10 x 45mm Bolt Sleeve M10 x 63mm Bolt Key User's Manual Exercise Guide Exercise Chart Decal
Note: "#" indicates a non-illustrated part. See the back cover of this manual for information about ordering replacement parts.
Qty.
Specifications are subject to change without notice. SAVE THIS PART LIST/EXPLODED DRAWING FOR FUTURE REFERENCE
81 WEEVSY49220
R0404A
Key No...
Instruction Manual - Page 16
EXPLODED DRAWING-Model No. WEEVSY49220 R0404A
60
61 21
9 62
61 9
62
84 23 66 70
78 18
83
57 33
7
71
76 50 7
74
27 77
77
9 ...
Weider 8150 Reviews
We have not received any reviews for Weider yet.