TRENDnet TEW-840APBO2K Support and Manuals
Get Help and Manuals for this TRENDnet item
View All Support Options Below
Free TRENDnet TEW-840APBO2K manuals!
Problems with TRENDnet TEW-840APBO2K?
Ask a Question
Free TRENDnet TEW-840APBO2K manuals!
Problems with TRENDnet TEW-840APBO2K?
Ask a Question
Popular TRENDnet TEW-840APBO2K Manual Pages
Quick Installation Guide - Page 2
Hardware Installation Before You Start 2. Hardware Setup and Configuration 3. Table of Contents
1 English
1.
Quick Installation Guide - Page 3
...• 2 x TEW-840APBO • Quick Installation Guide • 2 x Proprietary/Passive PoE injectors (24V DC, 0.6A) • Mounting Hardware
Minimum Requirements • Computer with a network port and web browser •A network switch or router with the TEW-840APBO. The RJ-... LAN port • 4 x RJ-45 network cables
Note: The TEW-840APBO does not support IEEE 802.3at/af PoE standards. 1.
Quick Installation Guide - Page 4
Hardware Setup and Configuration
1. Remove the cover of the access point by pulling and holding the bottom tab in the vertical direction down (based on the access point orientation below) and sliding the cover below away from the access point 7RAHL)nnv
Pull and hold tab
2 2.
Quick Installation Guide - Page 5
...: 840)00COODa Default Channel: 48
Unit 2
AP2 Model: TEW-840APBO IA IP Address: 192.168.10.51 Subnet Mask: 255.255.255.0 User Name: admin Password: XOO00CO( AP2 Mode: WDS Station API SSID: ... additional configuration is required. Note: By default, the TEW-840APBO access points are located. You can find the preconfigured access point settings on the device label beneath the cover where the Ethernet...
Quick Installation Guide - Page 6
lamia-41
LANE LAN1 PoE)
Cable Guide 4 Aside from the preconfigured WDS connection settings, the TEW-840APB0 access points will also be configured with the following default settings:
TEW-840APBO #1 IP Address: 192.168.10.50 Netmask (Subnet Mask): 255.255.255.0 IP Gateway (Default Gateway): 192.168.10.1 Primary DNS: 192.168.10.1 ...
Quick Installation Guide - Page 8
Make sure both access points are powered on approximately 15 ft. (5 m) apart from one another with front of access points directly facing each other. 9. TEW-840APBO #1
TEW-840APBO #2
15 ft. (5m) Fr,
LAN1 (PoE)
LAN1 (PoE)
PoE
LAN
PoE 6
Quick Installation Guide - Page 10
Hardware Installation
1. The cover includes cable openings to route the connected Ethernet cable(s) when installing. =Mgr
2. Insert the included fasteners through the holes located at the back of the access point
8 Reinstall the cover by lining up the guide into the notch as shown and push until the cover clips into place and is secured. 3.
Quick Installation Guide - Page 11
3. Wrap the fasteners around the pole where the access points will be installed. Note: When set to WDS station mode, the TEW-840APBO features WiFi signal strength connectivity LEDs located on the back of the access point to your network.
9 On the fasteners, insert the open end ...
Quick Installation Guide - Page 12
I o
Completed Installation Reference
i
)
((
i I
i i
) Internet
Modem Router! Building 1 10
0 m
O O
40_
i
Building 2
Quick Installation Guide - Page 13
... recycling advice. FC
Waste electrical an electronic products must accept any questions regarding the product installation, please contact our Technical Support. Check with your product online.
Note The Manufacturer is subject to this equipment. Toll free US/Canada: 1-855-373-4741 Regional phone numbers available at www.trendnet.comiregister
TEW-840APBO2K (V1) / 03.12.2019
Datasheet - Page 1
... housing • 1 x Gigabit PoE (in) port, and 1 x Gigabit port
TRENDnet's 14 dBi WiFi AC867 Outdoor PoE Preconfigured Point-to-Point Bridge Kit, model TEW-840APBO2K, provides longrange wireless AC867 point-to-point connectivity.This preconfigured outdoor WiFi bridge kit provides installers the simplest way to create a long-distance wireless point-to...
Datasheet - Page 2
TEW-840APBO2K
Preconfigured Point-to-Point Bridge
Reduce installation and setup time with a maximum distance of -10° - 60° C (14° - 140° F). NETWORKING SOLUTION PoE Power Adapters
Included proprietary PoE power adapters provide power ...
Datasheet - Page 3
TEW-840APBO2K
FEATURES
Preconfigured Kit Reduce installation and setup...8226; Scheduled auto reboot • CSMA/TDMA support • Preconfigured point-to-point ... static IP, DHCPv6) assignment • Email alert • Upgrade firmware • Backup/restore configuration • ... Pole and wall mount hardware included
SPECIFICATIONS
Standards • IEEE 802.3 •...
Datasheet - Page 4
... access point
Warranty • 3 year
Package Contents • 2 x TEW-840APBO • Quick Installation Guide • Proprietary/Passive PoE injectors (24V DC, 0.6A) • Mounting...in this document pertain to TRENDnet products and is subject to change without notice, and actual product appearance may affect performance. All Rights Reserved. TEW-840APBO2K
Modulation • 802....
TRENDnet TEW-840APBO2K Reviews
We have not received any reviews for TRENDnet yet.