TRENDnet TEW-410APB Support and Manuals
Get Help and Manuals for this TRENDnet item
This item is in your list!
View All Support Options Below
Free TRENDnet TEW-410APB manuals!
Problems with TRENDnet TEW-410APB?
Ask a Question
Free TRENDnet TEW-410APB manuals!
Problems with TRENDnet TEW-410APB?
Ask a Question
Popular TRENDnet TEW-410APB Manual Pages
Data Sheet - Page 1
... roaming capabilities for network cable installation.
The TEW410APB also provides AP-to-AP bridging functions, allowing users to wired LAN.
Security: Provides 64/128-bit WEP Encryption and MAC Address Access Control. TEW-410APB (07-01-2003)
Flexible: Works as hard drives, CD-ROM/DVD drives, network printers, and Internet connection. TRENDnet
TRENDware, USA
What's Next in...
Data Sheet - Page 2
...TRENDnet
Web: www.TRENDNET.com
TRENDware, USA
Email: [email protected]
TRENDnet is subject to Female Reverse SMA Connector)
TEW...TEW-410APB
54Mbps 802.11g Wireless Access Point + Bridge
SPECIFICATIONS...
Standards: • IEEE 802.3 (10Base-T), and IEEE 802.3u (100Base-TX), IEEE 802.11b (11Mbps) and IEEE 802.11g draft (54Mbps)
Protocols: • DHCP (Client), TCP/IP... Address ...
Manual - Page 3
Introduction...3 2. Primary Setup ...7 4.2. Operating Mode...12 4.4. Safety Notification 4 3. System...11 4.3. Troubleshooting ...22
User's Guide
2 Hardware Installation 5 4 Web Management Settings 6
4.1. Status...14 4.5 Traffic Log...15 4.6 AccessControl ...16 4.7 Advanced Wireless...17 4.8. Upgrade Firmware...20
5. Contents 1. SNMP...19 4.9.
Manual - Page 6
...admin
Password
admin
AP IP Address
192.168.1.250
AP Subnet Mask 255.255.255.0
RF ESSID
ap11g
11g RF Channel 6
Mode
11b+g
Encryption
Disabled
User's Guide
5 Used to connect to
default
3.
Firmware
upgrade
(first
1
Green Blink
1. Hardware Installation
Front Panel
The front panel provides LED's for approximately ten seconds, all configurations will set to factory default...
Manual - Page 7
... have input the correct password and logged-in the User Name box.
And input password "admin" on , be careful not to change the password.
Once you must login as administrator, it is writing to the Setup page screen.
The Security Settings section described later in this manual describes how to change the administrator password to ensure a secure protection...
Manual - Page 8
User's Guide
7
The default value is the AP's IP Address and Subnet Mask as seen on this screen. Primary Setup
MAKE CORRECT NETWORK SETTINGS OF YOUR COMPUTER To change the configuration, use Internet Explorer (IE) or Netscape Communicator to configure the AP and get it working properly using the settings on the
internal LAN.
4.1. Most users will be able to...
Manual - Page 10
... input the Pre-Shared Key. User's Guide
9 To use of WPA, ... by default. Please input the period of the OS must also support 802.1x protocol. The default selection is chosen), though the Operating System must installed 3er ... Integrity Code (MIC) to make right use WPA Pre-Shared Key, enter a password in alphanumeric. AES stands for Temporal Key Integrity Protocol. You can support it,...
Manual - Page 11
... RADIUS uses an external RADIUS server to save your RADIUS Server IP address. Please input the Authentication port of your algorithms method. The default selection is 300 seconds.
* Click Apply to perform user authentication. Please input your settings.
User's Guide
10 To use WPA RADIUS, enter the IP address of renewal time. You can select between TKIP or AES.
Manual - Page 18
.... The default setting is 100.
User's Guide
17 The default value is... AUTO.
Shared Key: Shared Key is only available if the WEP option is a packet broadcast by the AP to transmit the secret key in clear. Beacon Interval: The Beacon Interval value indicates the frequency interval of those who do not. Shared Key authentication supports...
Manual - Page 21
...the AP's settings before you want to the System section. User's Guide
20 Upgrade Firmware
To perform the firmware upgrade action, please go to use.
To upgrade the AP's firmware: 1.
4.9.
Download the firmware upgrade file from the internet. 2. Click the Firmware Upgrade button. 4. Firmware Upgrade: Click the Firmware Upgrade button to find the firmware upgrade file. Extract...
Manual - Page 23
... a different network cable.
User's Guide
22 LAN Connection Problems I can 't access my AP. The computer you are not connected properly. Make sure that corresponds to other adapter may damage your AP. Resolution: Connect the power adapter to 192.168.1.15 or another unique IP Address that your AP and plug it is set correctly.
Resolution: Make...
Manual - Page 24
... settings are set correctly. Make sure that your IP Address to make sure that may
cause interference. Check your computer is compatible with the Wireless AP. TRENDware Technical Support
Tel: +1-310-891-1100
Fax: +1-310-891-1111
E-mail: support@trendware.com www.trendware.com
Support Hours: 7:30AM ~ 6:00PM, Monday ~ Friday (except holidays)
User's Guide
23 Wireless Troubleshooting...
Quick Installation Guide - Page 4
... you must use your web browser and manually input http://192.168.1.250 into the Address box and press Enter. Once you must login as administrator, it is writing to the Setup page screen.
2 To start configure the Wireless 11g AP, you have input the correct password and logged-in about 5 seconds, because data...
Quick Installation Guide - Page 5
...the AP's basic setup functions. LAN IP Address and Subnet Mask: This is 192.168.1.250 for IP Address and 255.255.255.0 for Subnet Mask. Please Click "Apply" button to save your settings once you have... working properly using the settings on the internal LAN.
Most users will be able to connect the WEB management 192.168.1.250. The default value is the AP's IP Address and Subnet Mask as seen...
TRENDnet TEW-410APB Reviews
Do you have an experience with the TRENDnet TEW-410APB that you would like to share?
Earn 750 points for your review!
We have not received any reviews for TRENDnet yet.
Earn 750 points for your review!