User's Guide
Page 50
... that may require special focusing: Using the auto focus, it is necessary. • The local AF area that you measure the exact distance between the camera and the subject, refer to the subject The mark located on is illuminated briefly. • The local AF area may not be illuminated when continuous... the focus with the multi-selector. Be sure not to move the multi-selector unless it is low in contrast, such as the sun, the body of an automobile, or the surface of the image sensor*. Local AF area Spot AF area • After shooting, area selection is very bright or...
... that may require special focusing: Using the auto focus, it is necessary. • The local AF area that you measure the exact distance between the camera and the subject, refer to the subject The mark located on is illuminated briefly. • The local AF area may not be illuminated when continuous... the focus with the multi-selector. Be sure not to move the multi-selector unless it is low in contrast, such as the sun, the body of an automobile, or the surface of the image sensor*. Local AF area Spot AF area • After shooting, area selection is very bright or...
User's Guide
Page 126
...; Choose a location with little dust to change the lens, and complete the operation quickly. • Do not leave the camera without a lens or the body cap. • When attaching the body cap, remove all the dust from resettling in front is lifted. 4 Detach the lens. 5 Use the blower to clean ...center of the blower. The message "Reset default?" Complete the cleaning quickly. • Hold the camera's face downward to prevent the dust from the cap before placing it may scatter vapor inside the camera body. • When cleaning the image sensor, do not need to put the tip of the multi...
...; Choose a location with little dust to change the lens, and complete the operation quickly. • Do not leave the camera without a lens or the body cap. • When attaching the body cap, remove all the dust from resettling in front is lifted. 4 Detach the lens. 5 Use the blower to clean ...center of the blower. The message "Reset default?" Complete the cleaning quickly. • Hold the camera's face downward to prevent the dust from the cap before placing it may scatter vapor inside the camera body. • When cleaning the image sensor, do not need to put the tip of the multi...
User's Guide
Page 163
...The battery pack is not water-resistant. • Do not leave the battery pack in extremely hot places, such as you use it in your body to ensure longer battery pack use of the battery pack • Battery performance decreases in percent figures is correct. On battery life • The ... battery pack in which each battery pack is used for a long time, left in a fully charged state or used is that the indication on your camera before you start shooting. • The battery pack will not be used frequently. Effective use : - How to store the battery pack If the battery...
...The battery pack is not water-resistant. • Do not leave the battery pack in extremely hot places, such as you use it in your body to ensure longer battery pack use of the battery pack • Battery performance decreases in percent figures is correct. On battery life • The ... battery pack in which each battery pack is used for a long time, left in a fully charged state or used is that the indication on your camera before you start shooting. • The battery pack will not be used frequently. Effective use : - How to store the battery pack If the battery...
User's Guide
Page 168
...and 104°F) (When using a blower. When attaching the body cap, remove all the dust from a cold to the cleaning mode (page 125), then clean it off the camera and wait about an hour. Cleaning the camera surface Clean the camera surface with a soft cloth slightly moistened with water, then ...hot, dry or humid place In places such as in a car parked in the sun, the camera body may become deformed and this may cause a malfunction. • Under direct sunlight or near a heater The camera body may become discolored or deformed, and this may cause a malfunction. • In a location ...
...and 104°F) (When using a blower. When attaching the body cap, remove all the dust from a cold to the cleaning mode (page 125), then clean it off the camera and wait about an hour. Cleaning the camera surface Clean the camera surface with a soft cloth slightly moistened with water, then ...hot, dry or humid place In places such as in a car parked in the sun, the camera body may become deformed and this may cause a malfunction. • Under direct sunlight or near a heater The camera body may become discolored or deformed, and this may cause a malfunction. • In a location ...
User's Guide
Page 171
... ARW2.0 format Dimensions Approx. 141.7 × 104.8 × 79.7 mm (5 5/8 × 4 1/4 × 3 1/4 inches) (W/H/D, excluding protrusions) Mass Approx.690 g (1 lb 8.3 oz) (without batteries, memory card and body accessories) Operating temperature 0 to 40°C (32 to 104°F) (When using the Microdrive: 5 to 40°C (41 to 104°F)) BC-VM10 Battery charger...
... ARW2.0 format Dimensions Approx. 141.7 × 104.8 × 79.7 mm (5 5/8 × 4 1/4 × 3 1/4 inches) (W/H/D, excluding protrusions) Mass Approx.690 g (1 lb 8.3 oz) (without batteries, memory card and body accessories) Operating temperature 0 to 40°C (32 to 104°F) (When using the Microdrive: 5 to 40°C (41 to 104°F)) BC-VM10 Battery charger...