Instruction Manual
Page 19
Loosen screw (A) as illustrated. (1) - Should there be any problem, ask your local dealer for advice. 12 Unscrew the bulb and install a new one (C). (2) - B A 1 C 2 GB Changing the bulb Disconnect the machine from the power supply by removing the plug from the main socket! Remove the face plate (B). - Replace bulb with same type rated 10 watts (110-120V area) or 15 watts (220-240V area). - Replace the face plate and tighten screw.
Loosen screw (A) as illustrated. (1) - Should there be any problem, ask your local dealer for advice. 12 Unscrew the bulb and install a new one (C). (2) - B A 1 C 2 GB Changing the bulb Disconnect the machine from the power supply by removing the plug from the main socket! Remove the face plate (B). - Replace bulb with same type rated 10 watts (110-120V area) or 15 watts (220-240V area). - Replace the face plate and tighten screw.
Instruction Manual
Page 29
...new needle. (1) B. Damaged points 2 22 Insert the needle as illustrated as it is showing signs of the shaft should be in perfect condition. (2) Problems can occur with: A. Blunt needles C. B A C Needles must be towards the back. C/D. Insert the needle as far up as follows: A.... Attention: Turn power switch to off ("O") before inserting or removing the needle. The flat side of wear and causing problems. For best sewing results always use SINGER Brand Needles. D A B C 1 GB Inserting and changing needles Change the needle regularly, especially if it will go. Bent ...
...new needle. (1) B. Damaged points 2 22 Insert the needle as illustrated as it is showing signs of the shaft should be in perfect condition. (2) Problems can occur with: A. Blunt needles C. B A C Needles must be towards the back. C/D. Insert the needle as far up as follows: A.... Attention: Turn power switch to off ("O") before inserting or removing the needle. The flat side of wear and causing problems. For best sewing results always use SINGER Brand Needles. D A B C 1 GB Inserting and changing needles Change the needle regularly, especially if it will go. Bent ...
Instruction Manual
Page 31
... up left channel (6). Pull about 6-8 inches of the take thread behind the flat, horizontal thread guide. (8) - Thread tension module by not doing so several sewing problems could result. - Place the spool of spool holder next 1 to the needle which should be found on the holder with the thread coming off the...: For safety, it is important to carry out correctly as by leading thread down to spool. (3) - 3 7 68 9 6 4 54 5 3 2 7 8 9 GB Threading the upper thread This is a simple operation but it is strongly suggested you turn off the spool as shown.
... up left channel (6). Pull about 6-8 inches of the take thread behind the flat, horizontal thread guide. (8) - Thread tension module by not doing so several sewing problems could result. - Place the spool of spool holder next 1 to the needle which should be found on the holder with the thread coming off the...: For safety, it is important to carry out correctly as by leading thread down to spool. (3) - 3 7 68 9 6 4 54 5 3 2 7 8 9 GB Threading the upper thread This is a simple operation but it is strongly suggested you turn off the spool as shown.
Instruction Manual
Page 91
.... 2.Clean the hook and feed dog as described. Lubricate as described. 3.Only use good quality sewing machine oil. 4.Replace the needle. GB Trouble shooting guide Problem Upper thread breaks Lower thread breaks Cause 1.The machine is not threaded correctly. 2.The thread tension is too tight. 3.The thread is too thick for...
.... 2.Clean the hook and feed dog as described. Lubricate as described. 3.Only use good quality sewing machine oil. 4.Replace the needle. GB Trouble shooting guide Problem Upper thread breaks Lower thread breaks Cause 1.The machine is not threaded correctly. 2.The thread tension is too tight. 3.The thread is too thick for...
