Sanyo EF10NZ - SXGA LCD Projector Support and Manuals
Get Help and Manuals for this Sanyo item
View All Support Options Below
Free Sanyo EF10NZ manuals!
Problems with Sanyo EF10NZ?
Ask a Question
Free Sanyo EF10NZ manuals!
Problems with Sanyo EF10NZ?
Ask a Question
Popular Sanyo EF10NZ Manual Pages
Owners Manual - Page 1
Multimedia Projector
MODEL PLC-EF1OE PLC-EF10 PLC-EF1OEL (Without Lens)
c-D
0
OWNER'S INSTRUCTION MANUAL
Owners Manual - Page 2
... projection lens as the Laser Pointer function from the many service requests were not caused by problems that many features included in the manual. Eye damage may result in the event of theft or loss of unit Model No :
and retain this LCD projector, please
record the Model Number and Serial Number located on its side. IMPORTANT...
Owners Manual - Page 4
... PROJECTOR
5
TRADEMARKS
5
K.r07 offratt
NAME OF EACH PART OF THE PROJECTOR 6
SETTING-UP THE PROJECTOR
7
MOVING THE PROJECTOR
8
POWER REQUIREMENTS
9
TERMINAL OF THE PROJECTOR CONNECTING...Mode 1 or Mode 2) LAMP AGE
°A EN I
MEINTENANCE TEMPERATURE WARNING INDICATOR AIR FILTER CARE AND CLEANING LAMP REPLACEMENT CLEANING THE LENS
TROUBLESHOOTING TECHNICAL SPECIFICATIONS
50-51 50-51 50...
Owners Manual - Page 5
...are included.
Computer mode
--- Check to find all the parts are compressed to 1280 x 1024. The projector displays computer images just as they appear on your computer's... of Microsoft Corporation. • Other trademarks are missing, contact an authorized dealer or service station.
• Owner's Manual. • Wireless Remote Control Unit. • Remote Control Cable. • Graphic...
Owners Manual - Page 8
...service, use a Sanyo recommended Carrying Case. • Do not transport the projector by using a courier or transport service in an unsuitable transport case. AIR INTAKE VENT (BOTTOM SIDE)
MOVING THE PROJECTOR
A Use the carry handle when moving the projector. Pay attention to the following to the projector. Replace... the projector through the bottom vent. INSTALLATION
4pi
This projector is ...
Owners Manual - Page 9
... designed to work with single-phase power systems having a grounded neutral conductor. The projector is supplied to your authorized dealer or service station if you are not sure what type of power system. Consult your building. POWER REQUIREMENTS
INSTALLATION
Your projector uses nominal input voltages of 110-120 VAC. The socket-outlet must be...
Owners Manual - Page 12
...your computer and set-up the computer configuration following steps.
1.
Personal computers can be replaced by projector's remote control unit... REMOVAL HINT Disconnect control port cable with following instruction included in the Graphic Accelerator Board package. When... be connected to these terminals using this projector should be installed into your computer to these jacks using ...
Owners Manual - Page 15
... connecting the cable, the power cords of the computer and set up the computer following instructions in ) Graphic Accelerator Board (included within projector) into PCI bus slot of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.
15...
Owners Manual - Page 17
CONNECTING THE PROJECTOR
a
NOTE: This connction need optionally saled Graphic Accelerator PC card (GA-SM02P2/CB). INSTALL (PLUG) INTO PC CARD BUS SLOT
GRAPHIC ACCELERATOR...INPUT
INPUT
Before using with digital connection, install (Plug in) Graphic Accelerator PC card into card bus slot of the computer and set up the computer following instructions in the Graphic Accelerator PC
card package....
Owners Manual - Page 23
... end. SELECT BUTTON This button has different functions depending on . BEFORE OPERATION
LAMP REPLACEMENT INDICATOR Light is orange when the Lamp life draws to operate power lens shift. FOCUS BUTTONS Used to the projector's setting in MENU operation. Light is brightened when the projector is too high. Use this button, the POINT UP/DOWN/LEFT/RIGHT...
Owners Manual - Page 40
...(See "COMPATIBLE COMPUTER SPECIFICATIONS" on first.
2. display appears. Another
dialog box COMPUTER SYSTEM DISPLAY will appear. 4. To quit the MENU, move the arrow by the projector in most cases, ... and switch to manually set MODE SELECT to change the current display mode, move the arrow to use.
1. Press the SELECT (REAR CLICK) BUTTON to "COMPUTER", the projector will work in the...
Owners Manual - Page 50
... USB driver (optionally saled parts) and set up the computer following instruction in the " wireless remote control unit.
The Lamp is in the "On" position, the top/bottom picture reverse. " (Mouse) position, you project onto a rear projection screen.
The picture is in the "
" (Control) position, you control the projector by switching this function, turn the projector Lamp off...
Owners Manual - Page 51
.... Press the POINT LEFT/RIGHT BUTTON(s) to normal code (MODE 1), take same operation above.
-4,X•
4
1. The settings are system-up and used to set normal code (MODE 1) and the other one is extended code (MODE 2). OTHER FUNCTION SETTING
This projector can be operated with two different code, one is factory-set by pressing the POINT UP/DOWN BUTTON(s). 5. To...
Owners Manual - Page 55
... the image still does not display, unplug the projector from the computer and check the computer monitor's display. TROUBLESHOOTING
Before calling your equipment as described in order of cleaner. The
problem may be with your graphics controller rather than with the projector. (When you don't use the projector, replace the lens cover. Check cable connections. Abrasive...
Owners Manual - Page 57
... (R and L) x 2 sets HDB15-pin Terminal Phono Type (R and L) x 1 set
wow-
84
33339933*,
9 9
9314A„,. SP. Ampere) Model PLC-EF10E/EF10EL 7.2 A (Max...sets, Phono Type (Audio R and L) x 2 sets and DIN 4 pin (S-Video) x 2 sets
899;
, '4433
BNC Type {Video/Y, C/Cb (B-Y),Cr (R-Y)) x 1 set and DIN 4 pin (S-Video) x 1 set Wired Remote Jack and Serial port (DB 9) INT. Multi-media Projector...
Sanyo EF10NZ Reviews
We have not received any reviews for Sanyo yet.