Owner Manual
Page 6
... Amplifier • 110 Watts/Channel @ 8 ohms (FTC) • 170 Watts/Channel @ 6 ohms (IEC) • 185 Watts/Channel @ 6 ohms (JEITA) • WRAT-Wide Range Amplifier ... Accurate 32-bit Processing DSP Connections • 8 HDMI*8 Inputs (1 on front panel) and 2 Outputs • Onkyo Q for System Control • 5 Digital Inputs (2 Optical/3 Coaxial) • Component Video Switching (2 Inputs/1 Output...American models)/ DAB+ tuner module (European, Australian and Asian models) • Banana Plug-Compatible Speaker Posts*11 • Powered Zone 2 • Bi-Amping Capability for FL/FR with SBL...
... Amplifier • 110 Watts/Channel @ 8 ohms (FTC) • 170 Watts/Channel @ 6 ohms (IEC) • 185 Watts/Channel @ 6 ohms (JEITA) • WRAT-Wide Range Amplifier ... Accurate 32-bit Processing DSP Connections • 8 HDMI*8 Inputs (1 on front panel) and 2 Outputs • Onkyo Q for System Control • 5 Digital Inputs (2 Optical/3 Coaxial) • Component Video Switching (2 Inputs/1 Output...American models)/ DAB+ tuner module (European, Australian and Asian models) • Banana Plug-Compatible Speaker Posts*11 • Powered Zone 2 • Bi-Amping Capability for FL/FR with SBL...
Owner Manual
Page 13
... short the positive and negative wires. If you get the best from the wall outlet before connecting your speakers: • You can connect speakers with an impedance of between 4 and 16 ohms. If the impedance of any connections. • Read the instructions supplied with the table above. Doing ... the built-in accordance with your surround sound system, you need to do is 4 ohms or more, but less than one speaker to negative (-) terminals. To get them to the positive (+) side of each speaker terminal. Doing so may damage the AV receiver. • Don't connect one cable ...
... short the positive and negative wires. If you get the best from the wall outlet before connecting your speakers: • You can connect speakers with an impedance of between 4 and 16 ohms. If the impedance of any connections. • Read the instructions supplied with the table above. Doing ... the built-in accordance with your surround sound system, you need to do is 4 ohms or more, but less than one speaker to negative (-) terminals. To get them to the positive (+) side of each speaker terminal. Doing so may damage the AV receiver. • Don't connect one cable ...
Owner Manual
Page 46
... - - -" option. Note • These settings are not available in this section are between 6 and 16 ohms. ■ Speakers Type(Front) ` Normal: Select this if you've connected your front speakers normally. ` Bi-Amp: Select this setting, you can check the settings made by Audyssey MultEQ® XT Room ...sensitivity to match your CD player to the OPTICAL IN 1, you must assign "OPTICAL1" to 4 ohms. If you bi-amp the front speakers, you must change these settings, you cannot assign any speaker is 4 ohms or more but less than 6. ` 6ohms: Select if the impedances of the following cases: ...
... - - -" option. Note • These settings are not available in this section are between 6 and 16 ohms. ■ Speakers Type(Front) ` Normal: Select this if you've connected your front speakers normally. ` Bi-Amp: Select this setting, you can check the settings made by Audyssey MultEQ® XT Room ...sensitivity to match your CD player to the OPTICAL IN 1, you must assign "OPTICAL1" to 4 ohms. If you bi-amp the front speakers, you must change these settings, you cannot assign any speaker is 4 ohms or more but less than 6. ` 6ohms: Select if the impedances of the following cases: ...
Owner Manual
Page 92
...channels driven at 1 kHz, with a maximum total harmonic distortion of 0.7% (FTC) (Others) 7 ch × 170 W at 6 ohms, 1 kHz, 1 ch driven of 1 % (IEC) Maximum Effective Output Power (Asian) 7 ch × 185 W at 6 ohms, 1 kHz, 1 ch driven (JEITA) Dynamic Power* * IEC60268-Short-term maximum output power 250 W (3 Ω, Front) 220...dB, 50 Hz (BASS) ±10 dB, 20 kHz (TREBLE) Signal to Noise Ratio 106 dB (LINE, IHF-A) 80 dB (PHONO, IHF-A) Speaker Impedance 4 or 6 Ω - 16 Ω Video Section Input Sensitivity/Output Level and Impedance 1 Vp-p/75 Ω (Component and S-Video Y) ...
...channels driven at 1 kHz, with a maximum total harmonic distortion of 0.7% (FTC) (Others) 7 ch × 170 W at 6 ohms, 1 kHz, 1 ch driven of 1 % (IEC) Maximum Effective Output Power (Asian) 7 ch × 185 W at 6 ohms, 1 kHz, 1 ch driven (JEITA) Dynamic Power* * IEC60268-Short-term maximum output power 250 W (3 Ω, Front) 220...dB, 50 Hz (BASS) ±10 dB, 20 kHz (TREBLE) Signal to Noise Ratio 106 dB (LINE, IHF-A) 80 dB (PHONO, IHF-A) Speaker Impedance 4 or 6 Ω - 16 Ω Video Section Input Sensitivity/Output Level and Impedance 1 Vp-p/75 Ω (Component and S-Video Y) ...