Instruction Manual
Page 5
... the Control knob. 5 Determine the selection Turn the Control knob to select "YES", and then press the Control knob. Right 15 "Fader" Fader Rear 15 - The previous item is 44.1kHz). "Bass Center FRQ"*, "Bass Level", "Bass Q Factor"*, "Bass EXT"*, "Middle Center FRQ"*, "..."Level2"/ "OFF" "Balance" Balance Left 15 - Supplementing is displayed. 6 Exit the Audio Control mode Press and hold the [ ] button. 8 | KDC-X896/ KDC-BT852HD/ KDC-X496/ KDC-452U/ KMR-550U Contents Audio preset memory You can set the Audio control items. 1 Set the audio control items Refer to adjust, and then...
... the Control knob. 5 Determine the selection Turn the Control knob to select "YES", and then press the Control knob. Right 15 "Fader" Fader Rear 15 - The previous item is 44.1kHz). "Bass Center FRQ"*, "Bass Level", "Bass Q Factor"*, "Bass EXT"*, "Middle Center FRQ"*, "..."Level2"/ "OFF" "Balance" Balance Left 15 - Supplementing is displayed. 6 Exit the Audio Control mode Press and hold the [ ] button. 8 | KDC-X896/ KDC-BT852HD/ KDC-X496/ KDC-452U/ KMR-550U Contents Audio preset memory You can set the Audio control items. 1 Set the audio control items Refer to adjust, and then...
Instruction Manual
Page 28
...Does not answer the phone call at once. "99SEC": Automatically answers the phone call comes in. "1" - "0" - Function of KDC-X896, KDC-BT852HD Bluetooth setup Bluetooth detail setting You can configure the initial settings of 1 - 99 seconds. "-1" - "0" - "OFF" : ... Outputs sound from the front and rear speakers. "+1" ( : Factory setting) 5 Select a Bluetooth detail setting value and determine it is displayed. 2 Enter the Function setting mode Press and hold the [ ] button. 54 | KDC-X896/ KDC-BT852HD/ KDC-X496/ KDC-452U/ KMR-550U Contents English | ...
...Does not answer the phone call at once. "99SEC": Automatically answers the phone call comes in. "1" - "0" - Function of KDC-X896, KDC-BT852HD Bluetooth setup Bluetooth detail setting You can configure the initial settings of 1 - 99 seconds. "-1" - "0" - "OFF" : ... Outputs sound from the front and rear speakers. "+1" ( : Factory setting) 5 Select a Bluetooth detail setting value and determine it is displayed. 2 Enter the Function setting mode Press and hold the [ ] button. 54 | KDC-X896/ KDC-BT852HD/ KDC-X496/ KDC-452U/ KMR-550U Contents English | ...
Quick Start Guide
Page 10
...car's chassis again after use of the unit. Installation Before installation 1 .....1 2 .....2 3 .....4 4 .....4 5 (KDC-X896, KDC-BT852HD only) .....1 (3m) 10 | Quick Start Guide 2 WARNING • The unit can only be installed in a ... • Do not touch the metal parts of this unit during installation, consult your Kenwood dealer. • Disconnect the battery's negative terminal before installing the unit. • Insulate...both of the front output terminals or to both of the rear output terminals (do not mix front and rear terminals). To prevent a short circuit, do For example, if...
...car's chassis again after use of the unit. Installation Before installation 1 .....1 2 .....2 3 .....4 4 .....4 5 (KDC-X896, KDC-BT852HD only) .....1 (3m) 10 | Quick Start Guide 2 WARNING • The unit can only be installed in a ... • Do not touch the metal parts of this unit during installation, consult your Kenwood dealer. • Disconnect the battery's negative terminal before installing the unit. • Insulate...both of the front output terminals or to both of the rear output terminals (do not mix front and rear terminals). To prevent a short circuit, do For example, if...
Quick Start Guide
Page 11
The communication range becomes shorter depending on the car are metal objects near the Bluetooth antenna. (KDC-X896, KDC-BT852HD only) For Good Reception To assure good reception, note the following: • Communicate with the ignition key. Bluetooth antenna unit English | 11 ... the unit so that the faceplate will not hit the lid when it is an obstacle between this unit and the cell-phone. connector to a rear output terminal. • Connect the speaker wires correctly to a too strong signal. on the surrounding environment. Using wrong screws, could damage the unit....
The communication range becomes shorter depending on the car are metal objects near the Bluetooth antenna. (KDC-X896, KDC-BT852HD only) For Good Reception To assure good reception, note the following: • Communicate with the ignition key. Bluetooth antenna unit English | 11 ... the unit so that the faceplate will not hit the lid when it is an obstacle between this unit and the cell-phone. connector to a rear output terminal. • Connect the speaker wires correctly to a too strong signal. on the surrounding environment. Using wrong screws, could damage the unit....
Quick Start Guide
Page 12
.../ KCA-RC55MR, consult your KCA-RC107MR/ KCA-RC55MR manual. ⁄ • Speaker Impedance: 4 - 8 Ω To front left speaker To front right speaker To rear left speaker To rear right speaker White White/Black Gray Gray/Black Green Green/Black Purple Purple/Black Ignition key switch Car fuse box ACC Red (Ignition wire...
.../ KCA-RC55MR, consult your KCA-RC107MR/ KCA-RC55MR manual. ⁄ • Speaker Impedance: 4 - 8 Ω To front left speaker To front right speaker To rear left speaker To rear right speaker White White/Black Gray Gray/Black Green Green/Black Purple Purple/Black Ignition key switch Car fuse box ACC Red (Ignition wire...
Quick Start Guide
Page 13
Blue (Antenna control wire) ANT. SW FRONT REAR Fuse (10A) Rear output R L Front output Subwoofer output RL FM/AM antenna input Wiring harness (Accessory1) Microphone (Accessory5) (KDC-X896, KDC-BT852HD only) If no connections are using the optional power amplifier, connect this wire to the terminal that matches your navigation ...wire) P.CONT When using , connect either to the control terminal of the motor antenna, or to the power terminal for the KDC-X496, KDC-452U, and KMR-550U.) ⁄ To connect the Kenwood navigation system, consult your car is required. English | 13
Blue (Antenna control wire) ANT. SW FRONT REAR Fuse (10A) Rear output R L Front output Subwoofer output RL FM/AM antenna input Wiring harness (Accessory1) Microphone (Accessory5) (KDC-X896, KDC-BT852HD only) If no connections are using the optional power amplifier, connect this wire to the terminal that matches your navigation ...wire) P.CONT When using , connect either to the control terminal of the motor antenna, or to the power terminal for the KDC-X496, KDC-452U, and KMR-550U.) ⁄ To connect the Kenwood navigation system, consult your car is required. English | 13