Hitachi B13FI - 10 Inch Drill Press Support and Manuals
Get Help and Manuals for this Hitachi item
View All Support Options Below
Free Hitachi B13FI manuals!
Problems with Hitachi B13FI?
Ask a Question
Free Hitachi B13FI manuals!
Problems with Hitachi B13FI?
Ask a Question
Popular Hitachi B13FI Manual Pages
Instruction Manual - Page 4
... the Drill Press in moving parts, breakage of checking to overheat. An undersized cord will result in a drop in line voltage and in .
16. The table on page 6 shows the correct size to contain long hair.
12. SECURE WORK. Make sure switch is damaged should be properly repaired or replaced.
19. DO NOT OPERATE the tool...
Instruction Manual - Page 5
....
24. THIS DRILL PRESS is fully supported at high speeds. SECURE THE WORK. IF THE WORKPIECE overhangs the table such that it will not rock or twist. USE THE RECOMMENDED SPEED for unstable workpieces.
10. DO NOT USE fly cutters or multiple-part hold the work on this intstruction manual.
1. SPECIFIC SAFETY INSTRUCTIONS FOR THE DRILL PRESS
WARNING
For your...
Instruction Manual - Page 6
...
ELECTRICAL REQUIREMENTS
POWER SUPPLY AND MOTOR SPECIFICATIONS
WARNING
To avoid electrical hazards, fire hazards, or damage to a 115V, 15 Amp circuit and use a 15 Amp time delay fuse or circuit breaker. Connect to the tool, use proper circuit protection.
GROUNDING INSTRUCTIONS
receptacle box.
DO NOT MODIFY THE PLUG PROVIDED.
If repair or replacement of power and cause...
Instruction Manual - Page 7
... instruction or operator's manual for that accompany accessories.
WARNING
• To avoid injury from moisture, a protective coating has been applied to clean the drill press. Hex Wrench
J.
Feed Handle
F.
WARNING
To avoid fire or toxic reaction, never use any part is missing or damaged, do not plug the drill press in until the missing or damaged part is replaced...
Instruction Manual - Page 9
KNOW YOUR DRILL PRESS
Belt Guard Cover Cover Knob
Belt Pulleys
English
Table Support Lock
Spindle
ON/OFF Switch Chuck
Quill
Chuck
Feed Spring Spring Cover Chuck Key
Table Assembly
Motor
Belt Tension Lock Knob Head Locking Set Screw Column Collar Laser Guide Feed Handles Rack
Table Support
Table Crank
Column Support Base
Table Bevel Lock Bevel Scale
-9-
Instruction Manual - Page 10
... it . Lock the spindle to the column.
The cutting tool used in the drill press to bench.
FEED HANDLE - Combines with the handles.
TABLE CRANK - Support lock must be removed whenever the workpiece is mounted on . English
GLOSSARY OF TERMS
DRILL PRESS TERMS
BASE GUIDES -
DEPTH SCALE STOP NUTS - DRILL ON/OFF SWITCH - See the Spindle Speed Chart inside...
Instruction Manual - Page 11
... base, aligning the holes in
the column support with the help of rack.
6. Tighten with beveled edge down. Rotate table assembly around column. Slide rack into slot in bracket. 3. B
3 1
2
5
Slotted Screwdriver
8″ & 10″ Adjustable Wrench
4
Combination Wrench
Mallet
Framing Square
Combination Square
WARNING
The Drill Press is in beveled edge of reack engage...
Instruction Manual - Page 12
... according to the polarity indicated on the switch (3) to the drill press head, clean all sawdust and debris. When replacing the batteries, the laser guide should be removed, otherwise the chuck may come loose during operation. 1. Push the chuck (1) onto the spindle (2). English
INSTALLING BATTERY FOR LASER GUIDE (Fig. Turn on compartment. 3. Tighten.
- 12 - Align the head with...
Instruction Manual - Page 13
DRILL PRESS ADJUSTMENTS
CAUTION: All the adjustments for the operation of the
spring cap (2).
To use , some occasional readjustments may need adjustment if the tension causes the quill to return too rapidly or too slowly. 1.
Loosen the lock nut (1). 2. Tighten the bevel locking bolt (3). 5. NOTE: The table has been removed from the power source...
Instruction Manual - Page 14
.... 3. K
• Any adjustments to increase the laser power is forbidden. • When using the laser pointer, do not look directly into the laser beam. • If the laser pointer is stored for repair or adjustments. • On units equipped with the adjustable wrench. Even a laser beam of the drill press head counterclockwise. 2. Replace the jam nut (3) and tighten against the...
Instruction Manual - Page 16
... will stop screw (10 to the table. Q
2 3
1
YOUR PROTECTION
WARNING
To avoid being torn from parts thrown by the tool, or shattered, always properly support your own safety, always observe the SAFETY
INSTRUCTIONS listed here and on the side of three inches. (See instructions for operating your hand could contact the drill bit or other cutting tool. b. c.
To avoid...
Instruction Manual - Page 17
... for the specific operation and workpiece material. When drilling metal, it to brace the workpiece. Securely lock the head and support to the column, the table arm to the support, and the table to the table arm, before operating the drill press with the drill press to the table or provide auxiliary support. h. Never climb on the drill press table, it...
Instruction Manual - Page 19
...
TROUBLESHOOTING GUIDE
WARNING
• To avoid injury from an accidental start, turn on.
1.
Quill returns too slow or too 1. Resharpen drill bit. See BASIC DRILL
PRESS OPERATIONS section.
See ASSEMBLY INSTRUCTIONS section, INSTALLING BATTERY FOR LASER GUIDE.
- 19 - Loose motor pulley
3.
Use backup material. See BASIC DRILL PRESS
OPERATIONS section. Support workpiece...
Instruction Manual - Page 55
...Power Cable
1
327492 0052 Pulley Cover
1
327493 0053 Rocker Switch
1
327494 0054 Motor
1
327495 0055 Clamp Cord
2
327496 0056 Capacitor
1
327497 0057 Feed Handle
3
327498 0058 Laser Guide Ass'y
1
0059 Set...327480 0040 Cr.
I .D. Pan Hd. Pan Hd. English
PARTS LIST
10″ BENCH DRILL PRESS
ALWAYS ORDER BY PART NO. Re. Truss Hd. AND I.D. Pan Hd. Description
...
Parts List - Page 2
... Cover
1
327468 0028 Head
1
327469 0029 Knob
1
327470 0030 External Tool
M4
1
Lock Washer
Part No. Screw M5*0.8-10
3
327479 0039 Cr. Pan Hd. Screw M6*1.0-8
3
327481 0041 Cr. Re. Re. Re. B13F
Part No. Truss Hd. Pan Hd. English
PARTS LIST
10″ BENCH DRILL PRESS
ALWAYS ORDER BY PART NO. Pan Hd. Description
Size
Qty
327441 0001 Clamp-Cord...
Hitachi B13FI Reviews
We have not received any reviews for Hitachi yet.