Hitachi DV20VB2 - 1/2 Inch Hammer Drill Support and Manuals
Get Help and Manuals for this Hitachi item
View All Support Options Below
Free Hitachi DV20VB2 manuals!
Problems with Hitachi DV20VB2?
Ask a Question
Free Hitachi DV20VB2 manuals!
Problems with Hitachi DV20VB2?
Ask a Question
Popular Hitachi DV20VB2 Manual Pages
Instruction Manual - Page 3
... potentially hazardous situations which, if ignored, could result in this Instruction Manual. Hazards that has not been specifically recommended by WARNINGS on the power tool and in death or ... instructions in the sections which , if not avoided, may cause machine damage. English
IMPORTANT SAFETY INFORMATION
Read and understand all of this Instruction Manual and in the Instruction Manual ...
Instruction Manual - Page 4
... or pull the plug from heat, oil, sharp edges or moving parts. Keep cord away from a receptacle. Be sure switch is an increased risk of electric shock. (4) Do not abuse the cord. English
SAFETY
GENERAL SAFETY RULES
WARNING: Read and understand all instructions listed below, may result in electric shock, fire and/or serious...
Instruction Manual - Page 5
... serviced before using. Follow instructions in unexpected situations.
(6) Use safety equipment. Always wear eye protection. Proper footing and balance enables better control of injury. (2) When servicing a tool, use tool if switch does not turn it is unstable and may create a risk of this manual. Service or maintenance performed by qualified repair personnel. Service (1) Tool service...
Instruction Manual - Page 6
...tool for example- ALWAYS attach the side handle and securely grip the Hammer Drill. 6.
If maintenance or servicing requires the removal of the tool. 8. Hold tools by children, individuals ...right tool. NEVER touch moving parts. 7. Don't use power tools if the plastic housing or handle is cracked. Cracks in the Instruction Manual. 10. English
SPECIFIC SAFETY RULES AND SYMBOLS
1. ...
Instruction Manual - Page 7
... wipe plastic parts with soapy water and dry thoroughly.
20. Touching these active wiring or electric cable with this tool V volts Hz .......... no .......... revolutions per minute
7 English
14. The tool's motor air vent must be dropped or struck against hard materials inadvertently, it immediately and arrange for repairs by a Hitachi authorized service center.
17...
Instruction Manual - Page 8
Although this system has no external grounding, you must still follow these precautions: ⅜ Only Hitachi Authorized Service Center should disassemble or assemble this power
tool, and only genuine HITACHI replacement parts should be installed. ⅜ Clean the exterior of this Instruction Manual, including not using the power tool in wet environments. To keep the double insulation system ...
Instruction Manual - Page 9
... all safety instructions contained in this Instruction Manual is designed to assist you in this Instruction Manual may show details or attachments that differ from those on your own power tool.
NAME OF PARTS
Depth Gauge
Gear Shift Dial
Change Lever Housing Nameplate
Drill Chuck
Push Button
Handle Cover Stopper
Side Handle Switch Trigger
Speed Control Dial
SPECIFICATIONS
Fig...
Instruction Manual - Page 10
... cord When the work site is placed under appropriate conditions conforming to a receptacle while the switch is used, it may cause overheating, resulting in the OFF position.
Power switch Ensure that the power source to be replaced or repaired.
4. If such a faulty receptacle is in metal, wood and plastic. WARNING:
Damaged cord must be...
Instruction Manual - Page 11
... Set the side handle to a position that is suited to the mounting part.
Loosen
8. Tighten securely.
(3) To remove the bit, place the chuck
wrench into one of the
Chuck wrench
Drill ... position of the depth gauge in the counterclockwise direction. However, when drilling 1/4" (6.5 mm) or smaller holes, use a metalworking drill bit.
7. Fig. 2
Rotate the side handle grip in the ...
Instruction Manual - Page 12
... change lever to the left positions to switch easily
between IMPACT (rotation and impact)
and ROTATION (rotation only),
respectively. When switching, make sure that the switch is hard to drill mode. The spindle shaft will not only reduce drill efficiency, but may also damage the drill tip.
ⅷ Operating the Hammer Drill with the change lever between the right...
Instruction Manual - Page 13
...R marks are installed or removed. Turn the speed control dial clockwise for higher speed and counterclockwise for lower speed. (Fig. 9)
Speed control dial
Stopper
Low speed
Switch trigger
Fig. 9... when the drill bits and other various parts are provided on the body.)
L mark
CAUTION:
Always use the hammer drill with clockwise rotation, when using it as the trigger switch is pulled ...
Instruction Manual - Page 14
... pushing the stopper, it keeps the switched-on condition which is noted.
2.
Be careful not to switch power OFF and disconnect the plug from the work and
start a stalled drill. To maintain firm control, establish a good foothold, use , the Power tool should ONLY be disconnected by a Hitachi Authorized Service Center.
14 Keeping after use When...
Instruction Manual - Page 15
... are constantly being improved and modified to the Hitachi Authorized Service Center when requesting repair or other maintenance. Service parts list A: Item No. code numbers and/or design) may be observed. To assure that only authorized replacement parts will be used, all service and repairs must be carried out by a Hitachi Authorized Service Center, ONLY.
7. Used D: Remarks
CAUTION...
Instruction Manual - Page 16
...323050 1 (3) Depth Gauge (Code No. 303709 1 (4) Chuck Wrench (Code No. 987576 1
OPTIONAL ACCESSORIES sold separately
(1) Drill bit for use of any obligation on the part of the HITACHI.
16 Length
6-5/16" (160mm)
931776
6-5/16" (160mm)
931670
6-5/8" (170mm)
959615
NOTE: Specifications are subject to change without any obligation on the part of the HITACHI. The use with your...
Hitachi DV20VB2 Reviews
We have not received any reviews for Hitachi yet.