Hitachi G10SS - 4 Inch Angle Grinder Support and Manuals
Get Help and Manuals for this Hitachi item
View All Support Options Below
Free Hitachi G10SS manuals!
Problems with Hitachi G10SS?
Ask a Question
Free Hitachi G10SS manuals!
Problems with Hitachi G10SS?
Ask a Question
Most Recent Hitachi G10SS Questions
How Do You Change The Packing Gland Over To A New One As Mine Melted
(Posted by amacey 8 years ago)
Popular Hitachi G10SS Manual Pages
Instruction Manual - Page 3
...electric shock. refrigerators. Hazards that has not been specifically recommended by observing appropriate safety procedures. MEANINGS OF ...term "power tool" in all instructions listed below refers to lose control.
or moving parts.
c) Keep children and bystanders ... tool and in the Instruction Manual before it occurs, and by HITACHI. Use of the warnings listed below may cause machine ...
Instruction Manual - Page 4
...warning label.
in moving parts.
instruction manual. fragments.
4) Power...SPECIFIC SAFETY RULES AND SYMBOLS
used.
1. injury.
5) Service
e) Do not overreach. Do not wear loose clothing
tool is GREATER than 13,700/min for G10SS...
is dangerous and must be repaired. repair person using the tool
and..., have
type of the power tool
replacement parts. Always wear eye
Many accidents are...
Instruction Manual - Page 5
... a Hitachi authorized service center. 17. Confirm if there are going to a complete stop using on page 10). 21. NEVER allow the tool to electric shock. Prevent potential injuries to do the job of a guard or safety feature, be secure and tight.
14. NEVER use the grinder in the Instruction Manual.
10. Don't leave tool until repaired...
Instruction Manual - Page 6
...; Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this power tool,
and only genuine HITACHI replacement parts
should be installed. ⅜ Clean the exterior of this Instruction Manual, including not...solvents, gasoline or thinners on the nameplate.
SAVE THESE INSTRUCTIONS AND
MAKE THEM AVAILABLE TO OTHER USERS AND
OWNERS OF THIS TOOL!
6 "Double insulation" means that ...
Instruction Manual - Page 7
... cover
Tail cover Brush Cap
Packing gland
Side handle Wheel guard
Fig. 1
SPECIFICATIONS
Model Motor Power Source Current No-Load Speed Wheel Size:
external diam.
hole diam. NEVER operate, or attempt any maintenance on your own power tool.
English
FUNCTIONAL DESCRIPTION
NOTE: The information contained in this manual. Some illustrations in this Instruction Manual may show...
Instruction Manual - Page 8
...replaced or repaired.
Check the receptacle
7. Check your work , test
⅜ No flammable gas, liquid, or object at an angle that the power source to the power source requirements specified on ", and make appropriate repairs. the grinder...the wheel guard. ⅜ Install the wheel guard to the packing gland,
turn it to the angle suitable for Depressed Center Wheel
overheating...
Instruction Manual - Page 9
...
(1) Turn the disc grinder upsidedown so that ...G10SS and 13,000/min for heavy grinding of steel and other hand.
center wheel. Do no need to a complete stop.
Grind only with the notched part of the depressed
Tighten the wheel nut by using a new depressed center wheel in Fig. 4. grinder...grinder's own weight is most suitable for G12SS or more. Use proper grinding angle...
Instruction Manual - Page 10
...
removed.
10 CAUTION:
Using this grinder with a carbon brush which are fully tightened. Confirm that ⅜ Replacing carbon brushes:
they are
Use HITACHI carbon brush No. 21 indicated in the wheel, replace it immediately.
2. Inspecting the carbon brushes (Fig. 6)
NOTE:
The motor employs carbon brushes which is no crack or any of carbon Wear limit brush
21
0.24" (6mm)
0.67...
Instruction Manual - Page 11
...⅜ Wrench 1
(Code No. 936522 G10SS) (Code No. 938332Z G12SS) ⅜ Side Handle (Code No. 318312 1
NOTE: Specifications are constantly being improved and
Repair, modification and inspection of Hitachi modified to the Hitachi Authorized
servicing or replacement of parts because of power tools, the safety regulations and
repairs must be performed by a HITACHI
standards prescribed in...
Parts List - Page 1
E291
ELECTRIC TOOL PARTS LIST
DISC GRINDER Model G 10SS
2007 • 5 • 18 (E1)
1
2 3 4 5 6 7
16 17 18 19 20 21
22
23 24 25 26 27
28
29
30 31
41
501
8 9
10 11
32 34
35 33
36
44 43 42
45
47
46
48
502
12 13 14 15
37 38 39 40
51 50 49
52 53 54 Hitachi Power Tools
LIST NO.
Parts List - Page 2
...ARMATURE 220V
1
* 9 360-802E ARMATURE 230V-240V
1
10 328-177 FAN GUIDE
1
11 963-712 HEX.
HD. WHEELS 100MMX4T A36Q (25 PCS.) 1 ... KOR, TPE
40 938-307 PILLAR TERMINAL
1
--- 2 ---
* ALTERNATIVE PARTS
G 10SS 5 -- 07 TAPPING SCREW D4X65
2
* 12 340-705C STATOR ...308-386 MACHINE SCREW (W/SP. CODE NO. DESCRIPTION
NO. C. WASHER) M5X16 (BLACK) 2
24 301-949 SET PLATE
1
25 301-948 WHEEL...
Parts List - Page 3
PARTS
ITEM NO. USED
REMARKS
41
HITACHI LABEL
1
42 936-551 BRUSH CAP
2
43 999-021 CARBON BRUSH (1 PAIR)
2
44 313-777 BRUSH HOLDER
2
45 955-509 SWITCH (1P SCREW TYPE)
1 INCLUD. 35, 36
46 305-499 MACHINE SCREW (W/WASHER) M3....1 (CORD ARMOR D8.8) FOR USA, CAN
* 54 500-447Z CORD
1 (CORD ARMOR D8.8) FOR SYR
G 10SS
5 -- 07
* ALTERNATIVE PARTS
--- 3 --- DESCRIPTION
NO. CODE NO.
Parts List - Page 4
...1
615 302-098 GUIDE BASE
1
616 323-918 DUST COLLECTION ADAPTER (DISC GRINDER) 1
--- 4 ---
* ALTERNATIVE PARTS
Printed in Japan 5 ...-- 07 (070518N)
USED
REMARKS
1
1 FOR NZL, AUS, EUROPE, CHN, KOR, TPE
1 FOR USA, CAN
G 10SS
OPTIONAL ACCESSORIES
ITEM NO. DESCRIPTION
NO. STANDARD ACCESSORIES
ITEM NO. CODE NO.
CODE...
Hitachi G10SS Reviews
We have not received any reviews for Hitachi yet.