Gateway E-9510T Support and Manuals
Get Help and Manuals for this Gateway Computers item
View All Support Options Below
Free Gateway E-9510T manuals!
Problems with Gateway E-9510T?
Ask a Question
Free Gateway E-9510T manuals!
Problems with Gateway E-9510T?
Ask a Question
Popular Gateway E-9510T Manual Pages
Gateway 9510 Server User Guide - Page 37
... the chipset a power control command. Issue an IPMI command
Select the LCP display language
Set sensor refresh interval
Password setup
Remote access control
32
www.gateway.com Chapter 3: Maintaining Your Server
Menu
Control the server
Options
Boot flags (select from available boot flags) ■ Set the flag - as if done over LAN or by creating button pushes -
Gateway 9510 Server User Guide - Page 40
... or DOS-bootable CD. 2 Download the BMC update file from support.gateway.com. 3 Follow the instructions included with Boot Block and Force Firmware updates:
1 Follow the instructions in "Preventing static electricity discharge" on page 41. Important
If Gateway Server Manager (GSM) software is installed, it .
For additional information, see "Installing an Intel Management Module (IMM)" on...
Gateway 9510 Server User Guide - Page 42
... CD. 9 Download the BMC update file from support.gateway.com. 10 Follow the instructions included with the new files. This error message can be ignored.
11 Turn off the server, then disconnect the power cords and wait for the most current version of the firmware update, an error message 009 will be updated whenever you update the FRU/SDR, we recommend...
Gateway 9510 Server User Guide - Page 81
...module is installed, delete the password (if one has been set) and uninstall the GSM software prior to installing the IMM module. To correct this situation, you must also be updated at this time. A boot block firmware update must force a BMC firmware update.
Important
If Gateway Server Manager (GSM) software is initially installed in your server. 2 Follow the instructions in "Preventing...
Gateway 9510 Server User Guide - Page 106
... partition. www.gateway.com
101
Updating the BIOS
Updating the BIOS
If you need a new version of this guide. 2 Download the BIOS update from support.gateway.com. 3 Restart your server, then press F2 when the Gateway logo screen appears during
startup.
4 Record any custom BIOS settings you can damage your changes and
close the BIOS Setup utility.
7 Follow the instructions in the...
Gateway 9510 Server User Guide - Page 139
... tools to begin installation.
9 Set and verify the password. This option configures the current system as a RAID Server, which lets it register with the Registration Server for the RAID Server.
■ RAID Server - The default destination directory is C:\Program
Files\RAID Web Console.
8 Click on Next to configure and manage RAID drivers.
■ RAID Registration Server - This option...
Gateway 9510 Server User Guide - Page 150
Chapter 7
Troubleshooting
• Interpreting error messages and codes • Troubleshooting • Getting telephone support and training
If the suggestions in this chapter do not correct the problem, see "Telephone support" on page 168 for more information about how to get help.
145
Gateway 9510 Server User Guide - Page 154
....com
149
Also, make sure that you followed each instruction. Check your server ■ Your server was dropped ■ The case was damaged during shipment from Gateway, contact Gateway Customer Care. Battery replacement
If you have problems after installing a new CMOS battery, try :
■ Restart your server, then open the BIOS Setup utility by pressing and holding F2 while your...
Gateway 9510 Server User Guide - Page 161
... system configuration screen, if enabled. Log errors encountered during POST.
Check boot password if installed. Allocates memory for different BIOS modules. Take care of ESCD in memory test.
Build ACPI tables (if ACPI is supported). Update CMOS memory size from base memory.
Enable/disable NMI as selected. Chapter 7: Troubleshooting
Check point 40
50
52
60
75...
Gateway 9510 Server User Guide - Page 165
...S5.
160
www.gateway.com
The following table describes the types of checkpoints that include manual configured onboard peripherals,... 5) - ACPI runtime checkpoints
ACPI checkpoints are set to initialize different system buses. Indicates that are...Output Device Initialization (function 2) - Chapter 7: Troubleshooting
DIM code checkpoints
The Device Initialization Manager (DIM) gets...
Gateway 9510 Server User Guide - Page 166
... the IDE connector on the system board or controller card.
Troubleshooting
BIOS
The settings in the drive's documentation. ■ Open your server case and make sure that the pins are enabled. For more information, see "Installing drives" on page 93.
CD or DVD drive
Your server does not recognize a CD or DVD, or the CD...
Gateway 9510 Server User Guide - Page 169
... you do not have a problem with your Internet Service Provider (ISP) is not covered by your ISP technical support for help. ■ Make sure that the memory modules are installed correctly. Modem (telephone dial-up correctly.
Contact your server's warranty. Let the keyboard dry before using it . Memory
Memory errors were detected during server start up )" on...
Gateway 9510 Server User Guide - Page 196
BIOS menu Security
BIOS submenu
Setting nth Drive
Removable Drive
1st Drive
nth Drive
ATAPI CDROM ...from the available devices.)
Administrator Password is (Installed/Not installed) User Password is (Installed/Not installed) Set Admin Password (Set or clear Admin password) Set User Password (Set or clear User password) User Access Level
Clear User Password Fixed disk boot sector protection
...
Gateway 9510 Server User Guide - Page 218
... for troubleshooting 146 static electricity 41 screen cleaning 27 troubleshooting 166 SCSI determining failed drive 60 ID 59 installing drives 59 SDRAM see memory security set passwords 33 setting up in BIOS 33 supervisor password 33 system 33 user passwords 33 using password 33 Security menu BIOS Setup utility 100 serial number 168 serial port 5 Server menu BIOS Setup utility 100
www.gateway...
Gateway E-9510T Setup Poster - Page 1
... cards
tat'
1.1
•
2. Note: If you ordered your server with your Gateway E-9510T server
0:' Gateway®
In this box you will find: Your server Accessory box Power cord CDs (for stability. telOinSIMMEF.F-1
For instructions on removing server components, see your user guide on the System Companion CD. 1. WI*
A MAN E-9510 SETUP PSTR R1 09/05
I III
8
07702 5
85 1060 Remove...
Gateway E-9510T Reviews
We have not received any reviews for Gateway yet.