Declaration of Conformity
Page 1
Marine Navigation Equipment (Global Positioning System Receiver) GPSMAP 5x5 The undersigned does hereby declare that the equipment complies to which Conformity is Declared: Communications 1999/5/EC, 2004/108/EC EN 60945: 2002 Maritime Navigation and Radio Equipment - Estate, Romsey, Hampshire, SO51 9DL, U.K. General Requirements EN 60950-1:2001 Safety of Information Technology Equipment Manufactured by: Manufacture's Address: Authorised Representative: Type...
Marine Navigation Equipment (Global Positioning System Receiver) GPSMAP 5x5 The undersigned does hereby declare that the equipment complies to which Conformity is Declared: Communications 1999/5/EC, 2004/108/EC EN 60945: 2002 Maritime Navigation and Radio Equipment - Estate, Romsey, Hampshire, SO51 9DL, U.K. General Requirements EN 60950-1:2001 Safety of Information Technology Equipment Manufactured by: Manufacture's Address: Authorised Representative: Type...
Flush Mount Kit Instructions (multilingual)
Page 1
... into a flat panel. • Select an appropriately sized location for the unit. • Use the Flush Mount Template provided to obtain the best fit. 2. Using the 9/32" (7 mm) wrench, tighten the nuts without overtightening. • Slide the unit into place within the unit housing. • Connect the wiring harness, GPS antenna, and XM antenna (if applicable) to mount the unit. • Using a 3/8" (10 mm) drill bit, drill the pilot...
... into a flat panel. • Select an appropriately sized location for the unit. • Use the Flush Mount Template provided to obtain the best fit. 2. Using the 9/32" (7 mm) wrench, tighten the nuts without overtightening. • Slide the unit into place within the unit housing. • Connect the wiring harness, GPS antenna, and XM antenna (if applicable) to mount the unit. • Using a 3/8" (10 mm) drill bit, drill the pilot...
Flush Mount Kit Instructions (multilingual)
Page 2
Assembled unit and flush mount hardware Tension mount brackets Wing nuts Figure 2 NOTE: You must connect the wiring harness to the boat's power supply, GPS antenna, XM antenna (if applicable), and transducer (if applicable) per the installation instructions included with the four wing nuts. • Tighten the four wing nuts to secure the unit housing to the unit, then slide the unit into the unit housing until it snaps in place...
Assembled unit and flush mount hardware Tension mount brackets Wing nuts Figure 2 NOTE: You must connect the wiring harness to the boat's power supply, GPS antenna, XM antenna (if applicable), and transducer (if applicable) per the installation instructions included with the four wing nuts. • Tighten the four wing nuts to secure the unit housing to the unit, then slide the unit into the unit housing until it snaps in place...
Quick Reference Guide
Page 1
... Results Marking a Waypoint or Man Overboard (MOB) To mark your current location as a waypoint or as an MOB point. Use the map pointer ( ) to change (Name, Symbol, Depth, Water Temp, Comment, or Position). Create a Waypoint Editing or Deleting a Waypoint To edit an existing waypoint: 1. From the Home screen, select Information > User Data > Waypoints. 2. Select the waypoint attribute you want to highlight the waypoint on the Navigation chart: 1. OR Select Guide To when using a preprogrammed BlueChart® g2 Vision® card to use the map pointer...
... Results Marking a Waypoint or Man Overboard (MOB) To mark your current location as a waypoint or as an MOB point. Use the map pointer ( ) to change (Name, Symbol, Depth, Water Temp, Comment, or Position). Create a Waypoint Editing or Deleting a Waypoint To edit an existing waypoint: 1. From the Home screen, select Information > User Data > Waypoints. 2. Select the waypoint attribute you want to highlight the waypoint on the Navigation chart: 1. OR Select Guide To when using a preprogrammed BlueChart® g2 Vision® card to use the map pointer...
Quick Reference Guide
Page 2
... your manual setting. To clear the active track: From any chart except the Fish Eye 3D, select MENU > Waypoints & Tracks > Tracks > On. or its subsidiaries May 2009 190-01074-01 Rev. When the unit loses satellite signals, the green bars disappear and the position icon displays a flashing question mark. To switch between modes. POWER/ BACKLIGHT RANGE ROCKER MARK SELECT MENU HOME SELECT-Press to select highlighted items. HOME-Press to return to the route. From the Home screen, select Information > User Data > Routes > New Route...
... your manual setting. To clear the active track: From any chart except the Fish Eye 3D, select MENU > Waypoints & Tracks > Tracks > On. or its subsidiaries May 2009 190-01074-01 Rev. When the unit loses satellite signals, the green bars disappear and the position icon displays a flashing question mark. To switch between modes. POWER/ BACKLIGHT RANGE ROCKER MARK SELECT MENU HOME SELECT-Press to select highlighted items. HOME-Press to return to the route. From the Home screen, select Information > User Data > Routes > New Route...