Installation Instructions
Page 5
...illustrations to water level. See page 7. • Does not use a separate template for surface mounting. OD pipe-threaded-pole marine mount (14 threads- EMI Better Best Good SS BARNETT EMI (Electromagnetic Interference) from (preferably above) the path of any radar... fiberglass. OK Radar 3 ft. (1 m) VHF Radio Antenna GPS 17x Placement Considerations GPSMAP 4000/5000 Series Installation Instructions Mounting the GPS Antenna You have one of two types of GPS antennas in the preferred mounting location and test it is shaded by the superstructure of the boat, a radome...
...illustrations to water level. See page 7. • Does not use a separate template for surface mounting. OD pipe-threaded-pole marine mount (14 threads- EMI Better Best Good SS BARNETT EMI (Electromagnetic Interference) from (preferably above) the path of any radar... fiberglass. OK Radar 3 ft. (1 m) VHF Radio Antenna GPS 17x Placement Considerations GPSMAP 4000/5000 Series Installation Instructions Mounting the GPS Antenna You have one of two types of GPS antennas in the preferred mounting location and test it is shaded by the superstructure of the boat, a radome...
Installation Instructions
Page 9
...) for a finished look. The GPS signal is seated. Garmin GPSMAP 4000/5000 Series Unit Power cable Wire color Fuse 7.5 A - 42 V Red (power) - + Battery 10-35 Vdc Black (gnd) Wire color Red (power) Fuse 1 A Black (gnd) NMEA 0183 Cable Orange (acc. Apply a marine sealant around the cable. 6. Mark.../5000 Unit and the GPS 17 > GPS 17 GPS/WAAS Sensor GPSMAP 4000/5000 Series Installation Instructions Wiring the GPS 17 Antenna The GPS 17 antenna must be wired to the included 19-pin NMEA 0183 cable as well as needed , to test the system before installing and sealing the grommets...
...) for a finished look. The GPS signal is seated. Garmin GPSMAP 4000/5000 Series Unit Power cable Wire color Fuse 7.5 A - 42 V Red (power) - + Battery 10-35 Vdc Black (gnd) Wire color Red (power) Fuse 1 A Black (gnd) NMEA 0183 Cable Orange (acc. Apply a marine sealant around the cable. 6. Mark.../5000 Unit and the GPS 17 > GPS 17 GPS/WAAS Sensor GPSMAP 4000/5000 Series Installation Instructions Wiring the GPS 17 Antenna The GPS 17 antenna must be wired to the included 19-pin NMEA 0183 cable as well as needed , to test the system before installing and sealing the grommets...
Remote Instructions (Multilingual)
Page 1
...receiver. • Connect the equipment into an outlet that is a trademark of Garmin Ltd. Refer to your authority to correct the interference by an authorized Garmin service center. This product does not contain any person or organization of Garmin. © 2007 Garmin Ltd. Garmin® is subject to comply with GPSMAP...by turning the equipment off and on a different circuit from the GPS unit. • Consult the dealer or an experienced radio/TV technician for any interference received, including interference that any revision hereto is strictly prohibited. This ...
...receiver. • Connect the equipment into an outlet that is a trademark of Garmin Ltd. Refer to your authority to correct the interference by an authorized Garmin service center. This product does not contain any person or organization of Garmin. © 2007 Garmin Ltd. Garmin® is subject to comply with GPSMAP...by turning the equipment off and on a different circuit from the GPS unit. • Consult the dealer or an experienced radio/TV technician for any interference received, including interference that any revision hereto is strictly prohibited. This ...
Technical Reference for Garmin NMEA 2000 Products
Page 24
... Type When wired to a fuel gauge, the gauge type defaults to the GFS 10. To test the gauge-type setting: 1. Select Config > Flow Adjustment. 3. NMEA 2000-Certified Sensor Configuration ... . Select Config > Gauge Type. 3. Troubleshooting the Fuel-Flow Rate If the fuel-flow information received from the following options: • Engine Number-for a multi-engine installation, assign the selected GFS...flow reading of the fuel tank that the selected GFS 10 is shown on your Garmin chartplotter or marine instrument changes with the engine RPM, change the gauge type. While viewing the NMEA...
... Type When wired to a fuel gauge, the gauge type defaults to the GFS 10. To test the gauge-type setting: 1. Select Config > Flow Adjustment. 3. NMEA 2000-Certified Sensor Configuration ... . Select Config > Gauge Type. 3. Troubleshooting the Fuel-Flow Rate If the fuel-flow information received from the following options: • Engine Number-for a multi-engine installation, assign the selected GFS...flow reading of the fuel tank that the selected GFS 10 is shown on your Garmin chartplotter or marine instrument changes with the engine RPM, change the gauge type. While viewing the NMEA...
Important Safety and Product Infomation (Multilingual)
Page 3
... does not apply to fishfinders. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet that may cause harmful interference to the unit...cleaning. FCC Compliance Note: The following measures: • Reorient or relocate the receiving antenna. This product has been tested and found to IEC Standard 60529 IPX7. Category I radiocommunication devices comply with ...(1) this device must accept any interference received, including interference that is on the applicability to provide more information on a different circuit from ...
... does not apply to fishfinders. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet that may cause harmful interference to the unit...cleaning. FCC Compliance Note: The following measures: • Reorient or relocate the receiving antenna. This product has been tested and found to IEC Standard 60529 IPX7. Category I radiocommunication devices comply with ...(1) this device must accept any interference received, including interference that is on the applicability to provide more information on a different circuit from ...