Fujitsu MHU2100AT - Mobile 100 GB Hard Drive Support and Manuals
Get Help and Manuals for this Fujitsu item
View All Support Options Below
Free Fujitsu MHU2100AT manuals!
Problems with Fujitsu MHU2100AT?
Ask a Question
Free Fujitsu MHU2100AT manuals!
Problems with Fujitsu MHU2100AT?
Ask a Question
Popular Fujitsu MHU2100AT Manual Pages
Manual/User Guide - Page 1
... information about handling this hard disk drive and the system installation procedure, refer to the following Integration Guide. CHAPTER 3 Installation Conditions
3.1 Dimensions 3.2 Mounting 3.3 Cable Connections 3.4 Jumper Settings
This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives.
Manual/User Guide - Page 2
Figure 3.1 Dimensions
3-2
C141-E202-01EN All dimensions are in mm. Installation Conditions
3.1 Dimensions
Figure 3.1 illustrates the dimensions of the disk drive and positions of the mounting screw holes.
Manual/User Guide - Page 3
3.2 Mounting
3.2 Mounting
For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation Figure 3.2 illustrates the allowable orientations for the disk drive. gravity
(a) Horizontal -1
(b) Horizontal -1
(c) Vertical -1
gravity (d) Vertical -2
gravity
(e) Vertical -3
(f) Vertical -4
Figure 3.2 Orientation
C141-E202-01EN
3-3
Manual/User Guide - Page 4
...to the system frame, do not allow the system frame to touch parts (cover and base) other than parts to which the HDD is not possible to SG. Bottom surface ...specification in Figure 3.3.
if it is attached.
(3) Limitation of mounting
Note) These dimensions are recommended values;
The mounting frame is zero. Installation Conditions
(2) Frame
The MR head bias of the HDD disk enclosure...
Manual/User Guide - Page 6
... in particular, receives sufficient cooling. Installation Conditions
(4) Ambient temperature The temperature conditions for a disk drive mounted in a cabinet refer to prevent the DE surface temperature from the disk drive. Figure 3.5 shows the temperature measurement point.
1
•
Figure 3.5 Surface temperature measurement points
Table 3.1 Surface temperature measurement points and standard...
Manual/User Guide - Page 7
... board, but hold it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. C141-E202-01EN
3-7 Damage: Do not press the cover of the disk drive. 3.2 Mounting
(5) Service area Figure 3.6 shows how the drive must be accessed (service areas) during and after installation.
Mounting screw hole
Cable connection
Mounting screw hole Figure...
Manual/User Guide - Page 8
... carrying.
Recommended equipments
ESD Shock
Contents Wrist strap ESD mat Low shock driver
Model JX-1200-3056-8 SKY-8A (Color Seiden Mat) SS-6500
Maker ...occasionally damaged by the impact of the driver.
(2) Please observe the tightening torque of a low impact when you use an electric driver.
Do not drop.
Installation
(1) Please use the driver of the screw strictly. ESD mat
...
Manual/User Guide - Page 9
3.3 Cable Connections
3.3 Cable Connections
3.3.1 Device connector
The disk drive has the connectors and terminals listed below for connecting external devices.
Figure 3.8 shows the locations of these connectors and terminals. Connector,
PCA
setting pins
Figure 3.8 Connector locations
C141-E202-01EN
3-9
Manual/User Guide - Page 10
... the interface is designed for ribbon cables and not for the cable connectors. Installation Conditions
3.3.2 Cable connector specifications Table 3.2 lists the recommended specifications for cables carrying differential signals.
3.3.3 Device connection
Figure 3.9 shows how to connect the devices. Host system
ATA-cable
Disk Drive #0
ATA-cable
DC Power supply
Power supply cable
Disk Drive...
Manual/User Guide - Page 11
Figure 3.10 Power supply connector pins (CN1)
3.4 Jumper Settings
3.4.1 Location of setting jumpers Figure 3.11 shows the location of the power supply connector (CN1).
Figure 3.11 Jumper location
C141-E202-01EN
3-11 3.4 Jumper Settings
3.3.4 Power supply connector (CN1) Figure 3.10 shows the pin assignment of the jumpers to select drive configuration and functions.
Manual/User Guide - Page 12
... the default setting position at the factory.
Open
1
CA
2
DB
Open
(a) Master drive
1
CA
Open
Short
2
DB
(b) Slave drive
Figure 3.13 Jumper setting of master or slave drive
Note: Pins A and C should be open.
3-12
C141-E202-01EN Open
Figure 3.12 Factory default setting
3.4.3 Master drive-slave drive setting Master drive (disk drive #0) or slave drive (disk drive #1) is selected...
Manual/User Guide - Page 13
... drive. 3.4.4 CSEL setting Figure 3.14 shows the cable select (CSEL) setting.
3.4 Jumper Settings
Open
1
CA
2
DB
Short
Note: The CSEL setting is set to low level.
Figure 3.14 CSEL setting
Figure 3.15 and 3.16 show examples of the cable and connecting it to ground further, the CSEL is set to the CSEL conductor, the CSEL is not depended on setting between pins Band...
Manual/User Guide - Page 14
Installation Conditions
drive
drive
Figure 3.16 Example (2) of Cable Select
3.4.5 Power Up in Standby setting When pin C is grounded, the drive does not spin up at power on.
3-14
C141-E202-01EN
Fujitsu MHU2100AT Reviews
We have not received any reviews for Fujitsu yet.