Manual/User Guide
Page 9
Connector, PCA setting pins Figure 3.8 Connector locations C141-E202-01EN 3-9 3.3 Cable Connections 3.3 Cable Connections 3.3.1 Device connector The disk drive has the connectors and terminals listed below for connecting external devices. Figure 3.8 shows the locations of these connectors and terminals.
Connector, PCA setting pins Figure 3.8 Connector locations C141-E202-01EN 3-9 3.3 Cable Connections 3.3 Cable Connections 3.3.1 Device connector The disk drive has the connectors and terminals listed below for connecting external devices. Figure 3.8 shows the locations of these connectors and terminals.
Manual/User Guide
Page 10
... interface is designed for ribbon cables and not for the cable connectors. Table 3.2 Cable connector specifications ATA interface and power supply cable (44-pin type) Name Cable socket (44-pin type) Model 89361-144 Manufacturer FCI IMPORTANT For the host interface cable, use a ribbon cable. Installation Conditions 3.3.2 Cable connector specifications Table 3.2 .... A twisted cable or a cable with wires that have become separated from the ribbon may cause crosstalk between signal lines. Host system ATA-cable Disk Drive #0 ATA-cable DC Power supply Power supply cable Disk...
... interface is designed for ribbon cables and not for the cable connectors. Table 3.2 Cable connector specifications ATA interface and power supply cable (44-pin type) Name Cable socket (44-pin type) Model 89361-144 Manufacturer FCI IMPORTANT For the host interface cable, use a ribbon cable. Installation Conditions 3.3.2 Cable connector specifications Table 3.2 .... A twisted cable or a cable with wires that have become separated from the ribbon may cause crosstalk between signal lines. Host system ATA-cable Disk Drive #0 ATA-cable DC Power supply Power supply cable Disk...
Manual/User Guide
Page 11
Figure 3.10 Power supply connector pins (CN1) 3.4 Jumper Settings 3.4.1 Location of setting jumpers Figure 3.11 shows the location of the power supply connector (CN1). Figure 3.11 Jumper location C141-E202-01EN 3-11 3.4 Jumper Settings 3.3.4 Power supply connector (CN1) Figure 3.10 shows the pin assignment of the jumpers to select drive configuration and functions.
Figure 3.10 Power supply connector pins (CN1) 3.4 Jumper Settings 3.4.1 Location of setting jumpers Figure 3.11 shows the location of the power supply connector (CN1). Figure 3.11 Jumper location C141-E202-01EN 3-11 3.4 Jumper Settings 3.3.4 Power supply connector (CN1) Figure 3.10 shows the pin assignment of the jumpers to select drive configuration and functions.
Manual/User Guide
Page 12
Installation Conditions 3.4.2 Factory default setting Figure 3.12 shows the default setting position at the factory. Open 1 CA 2 DB Open (a) Master drive 1 CA Open Short 2 DB (b) Slave drive Figure 3.13 Jumper setting of master or slave drive Note: Pins A and C should be open. 3-12 C141-E202-01EN Open Figure 3.12 Factory default setting 3.4.3 Master drive-slave drive setting Master drive (disk drive #0) or slave drive (disk drive #1) is selected.
Installation Conditions 3.4.2 Factory default setting Figure 3.12 shows the default setting position at the factory. Open 1 CA 2 DB Open (a) Master drive 1 CA Open Short 2 DB (b) Slave drive Figure 3.13 Jumper setting of master or slave drive Note: Pins A and C should be open. 3-12 C141-E202-01EN Open Figure 3.12 Factory default setting 3.4.3 Master drive-slave drive setting Master drive (disk drive #0) or slave drive (disk drive #1) is selected.
Manual/User Guide
Page 13
... not connected to the CSEL conductor, the CSEL is not depended on setting between pins Band D. drive drive Figure 3.15 Example (1) of the slave drive does not have a conductor. 3.4.4 CSEL setting Figure 3.14 shows the cable select (CSEL) setting. 3.4 Jumper Settings Open 1 CA 2 DB Short Note... the CSEL of Cable Select C141-E202-01EN 3-13 By connecting the CSEL of the master drive to ground further, the CSEL is identified as a slave drive. The drive is identified as a master drive. Figure 3.14 CSEL setting Figure 3.15 and 3.16 show examples of the cable and connecting...
... not connected to the CSEL conductor, the CSEL is not depended on setting between pins Band D. drive drive Figure 3.15 Example (1) of the slave drive does not have a conductor. 3.4.4 CSEL setting Figure 3.14 shows the cable select (CSEL) setting. 3.4 Jumper Settings Open 1 CA 2 DB Short Note... the CSEL of Cable Select C141-E202-01EN 3-13 By connecting the CSEL of the master drive to ground further, the CSEL is identified as a slave drive. The drive is identified as a master drive. Figure 3.14 CSEL setting Figure 3.15 and 3.16 show examples of the cable and connecting...