Fujitsu MHY2120BH - Mobile 120 GB Hard Drive Support and Manuals
Get Help and Manuals for this Fujitsu item
View All Support Options Below
Free Fujitsu MHY2120BH manuals!
Problems with Fujitsu MHY2120BH?
Ask a Question
Free Fujitsu MHY2120BH manuals!
Problems with Fujitsu MHY2120BH?
Ask a Question
Fujitsu MHY2120BH Videos
Notebook 120GB Fujitsu MHY2120BH S-ATA [10471] - m-ware.de
Duration: :36
Total Views: 158
Duration: :36
Total Views: 158
Notebook 120GB Fujitsu MHW2120BH S-ATA [10470] - m-ware.de
Duration: :36
Total Views: 10
Duration: :36
Total Views: 10
Popular Fujitsu MHY2120BH Manual Pages
Manual/User Guide - Page 1
CHAPTER 3 Installation Conditions
3.1 Dimensions 3.2 Mounting 3.3 Connections with Host System
This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives.
C141-E262
3-1
Manual/User Guide - Page 2
... user tap to the center of the connector
pins *5 Dimension from the outer edge of the user tap to the innermost edge of the disk drive. Installation Conditions
3.1 Dimensions
Figure 3.1 illustrates the dimensions of the
connector pins
Figure 3.1 Dimensions
3-2
C141-E262
Manual/User Guide - Page 3
...
3.2 Mounting
For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)."
(1) Orientation The disk drives can be 0.49N•m (5kgf•cm).
The mounting frame is attached. C141-E262
3-3 Use M3 screw for the mounting screw and the screw length should satisfy the specification in any direction.
(2) Frame
The MR head...
Manual/User Guide - Page 4
Bottom surface mounting
DE
2 A
Frame of system cabinet
2.5 2.5
2.5
Side surface
2.5
mounting
PCA
B
Frame of system
cabinet
3.0 or less
Screw
Details of mounting
Note) These dimensions are recommended values;
if it is not possible to satisfy them, contact us. Installation Conditions
(3) Limitation of A
3.0 or less
Screw
Figure 3.2 Mounting frame structure
3-4
C141-E262
Manual/User Guide - Page 5
For breather hole of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. Figure 3.3 Location of breather hole is shown as Figure 3.3.
3.2 Mounting
Because of breather hole mounted to the HDD, do not allow this to block. Locating of breather
C141-E262
3-5
Manual/User Guide - Page 6
...temperature must meet the standards listed in particular, receives sufficient cooling. Measurement point
Temperature
1
DE cover
60 °C max
3-6
C141-E262 Installation Conditions
(4) Ambient temperature
The temperature conditions for a disk drive mounted in Section 1.4, and the airflow must be considered to the ambient temperature at a point 3 cm from exceeding 60 °C. Figure...
Manual/User Guide - Page 7
... touch the printed circuit board, but hold it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. Static: When handling the device, disconnect the body ground (500 kΩ or greater). 3.2 Mounting
(5) Service area Figure 3.5 shows how the drive must be accessed (service areas) during and after installation. C141-E262
3-7
Manual/User Guide - Page 8
...
Wrist strap Use the Wrist strap.
Do not stack when carrying.
Do not place HDD vertically to avoid falling down. Installation
(1) Please use the driver of the screw strictly. Recommended equipments
ESD Shock
Contents Wrist strap ESD mat
Low shock driver
Model JX-1200-3056-8 SKY-8A (Color Seiden Mat)
SS-6500
Maker SUMITOMO 3M...
Manual/User Guide - Page 9
3.3 Connections with Host System
3.3 Connections with Host System
3.3.1 Device connector
The disk drive has the SATA interface connectors listed below for connecting external devices. Figure 3.7 shows the locations of these connectors and terminals.
SATA interface and power connectors
PCA
Figure 3.7 Connector locations
C141-E262
3-9
Manual/User Guide - Page 10
Installation Conditions
3.3.2 Signal segment and power supply segment Figure 3.8 shows each segment of requirements about SATA interface connector, refer to the "Serial-ATA Revision ...Connector specifications for mating with the disk drive must be compliant with Serial-ATA Revision 2.5 specification. Power supply segment
Signal segment
View from the connector side
P1 pins in the power S1 ...
Manual/User Guide - Page 11
... are snugly and securely in position.
Accordingly, be compliant with the Serial ATA Revision 2.5 specification.
3.3.5 Note about SATA interface cable connection Take note of the following precaution about plugging a SATA interface cable into the SATA interface connector of the disk drive and plugging the connector into a host receptacle:
When plugging together the disk...
Fujitsu MHY2120BH Reviews
We have not received any reviews for Fujitsu yet.