User's Guide
Page 3
... Ethernet Ports 7 16 1-Gigabit Ethernet Ports 8 24 1-Gigabit Ethernet Ports + 2 SFP Combo ports 8 48 1-Gigabit Ethernet Ports 8 Features 9 General Features 9 MAC Address Supported Features 11 Layer 2 Features 11 VLAN Supported Features 12 Class of Service (CoS) Features 12 Ethernet Switch Management Features 13 Port Default Settings 13 2 Hardware Description Switch Port Configurations 15 PowerConnect 2708/2716/2724/2748 Front Panel Port...
... Ethernet Ports 7 16 1-Gigabit Ethernet Ports 8 24 1-Gigabit Ethernet Ports + 2 SFP Combo ports 8 48 1-Gigabit Ethernet Ports 8 Features 9 General Features 9 MAC Address Supported Features 11 Layer 2 Features 11 VLAN Supported Features 12 Class of Service (CoS) Features 12 Ethernet Switch Management Features 13 Port Default Settings 13 2 Hardware Description Switch Port Configurations 15 PowerConnect 2708/2716/2724/2748 Front Panel Port...
User's Guide
Page 8
...-SX or 1000BASE-LX). 48 1-Gigabit Ethernet Ports The following figure illustrates the PowerConnect 2716 front panel. PowerConnect 2748 Front Panel 8 16 1-Gigabit Ethernet Ports The following figure illustrates the PowerConnect 2748 front panel. PowerConnect 2716 Front Panel The PowerConnect 2716 switch supports 16 GbE copper ports. 24 1-Gigabit Ethernet Ports + 2 SFP Combo ports The following figure illustrates the PowerConnect 2724 front panel. Figure...
...-SX or 1000BASE-LX). 48 1-Gigabit Ethernet Ports The following figure illustrates the PowerConnect 2716 front panel. PowerConnect 2748 Front Panel 8 16 1-Gigabit Ethernet Ports The following figure illustrates the PowerConnect 2748 front panel. PowerConnect 2716 Front Panel The PowerConnect 2716 switch supports 16 GbE copper ports. 24 1-Gigabit Ethernet Ports + 2 SFP Combo ports The following figure illustrates the PowerConnect 2724 front panel. Figure...
User's Guide
Page 18
Figure 2-7. On the top right side of a combo port can switch from the RJ-45 to indicate the port status. PowerConnect 2748 Back Panel 18 PowerConnect 2748 Front Panel On the front panel, there are 48 ports, which are present, the SFP port will be the active port, whereas the RJ-45 port will be used at any one of the two...
Figure 2-7. On the top right side of a combo port can switch from the RJ-45 to indicate the port status. PowerConnect 2748 Back Panel 18 PowerConnect 2748 Front Panel On the front panel, there are 48 ports, which are present, the SFP port will be the active port, whereas the RJ-45 port will be used at any one of the two...
User's Guide
Page 48
...Current Advertisement - The Backpressure mode is , occupy the link so it possible to operate). Flow Control can be enabled on the port. The synchronized port duplex mode of transmission: Max Capability, 10 Mbps at Half Duplex, 10 Mbps at Full Duplex, 100 Mbps at Half Duplex,...are : MDIX (Media Dependent Interface with higher speed devices by setting this field. Admin Duplex - Use for end stations. 48 The actual synchronized port speed, in one direction only at Full Duplex. Transmission is connected to ensure that the switch interface supports transmission between the...
...Current Advertisement - The Backpressure mode is , occupy the link so it possible to operate). Flow Control can be enabled on the port. The synchronized port duplex mode of transmission: Max Capability, 10 Mbps at Half Duplex, 10 Mbps at Full Duplex, 100 Mbps at Half Duplex,...are : MDIX (Media Dependent Interface with higher speed devices by setting this field. Admin Duplex - Use for end stations. 48 The actual synchronized port speed, in one direction only at Full Duplex. Transmission is connected to ensure that the switch interface supports transmission between the...
User's Guide
Page 70
... on a per -system basis. Egress queues are configured with lower priority. DSCP Mapping to Egress Queue Default Values DSCP Value 0-15 16-31 32-47 48-63 Forwarding Queue Values q1 (Lowest Priority) q2 q3 q4 (Highest Priority) CoS Services After packets are assigned to a specific egress queue, CoS services can... traffic over less time-sensitive applications. The following methods: • Strict Priority - Packets arriving untagged are assigned a default VPT value, which is set on a per port basis. The assigned VPT is used to map the packet to priority queues.
... on a per -system basis. Egress queues are configured with lower priority. DSCP Mapping to Egress Queue Default Values DSCP Value 0-15 16-31 32-47 48-63 Forwarding Queue Values q1 (Lowest Priority) q2 q3 q4 (Highest Priority) CoS Services After packets are assigned to a specific egress queue, CoS services can... traffic over less time-sensitive applications. The following methods: • Strict Priority - Packets arriving untagged are assigned a default VPT value, which is set on a per port basis. The assigned VPT is used to map the packet to priority queues.