Dell PowerConnect 5548 Support and Manuals
Get Help and Manuals for this Dell item
View All Support Options Below
Free Dell PowerConnect 5548 manuals!
Problems with Dell PowerConnect 5548?
Ask a Question
Free Dell PowerConnect 5548 manuals!
Problems with Dell PowerConnect 5548?
Ask a Question
Most Recent Dell PowerConnect 5548 Questions
How To Remove Static Ip Powerconnect 5548
(Posted by sanyado 9 years ago)
Powerconnect 5548 What Type Of Hdmi
(Posted by RCalje 9 years ago)
How To Change Interface Ip Address On Dell Powerconnect 5548
(Posted by golreespb 9 years ago)
What Is The Password On My Dell Powerconnect 5548
(Posted by rousja 9 years ago)
How To Change Stack Unit Id To A Dell 5548 Switch
(Posted by weMorgan 9 years ago)
Dell PowerConnect 5548 Videos
Dell PowerConnect 5548 $1950 Price Reduction
Duration: :34
Total Views: 46
Duration: :34
Total Views: 46
Popular Dell PowerConnect 5548 Manual Pages
User Guide - Page 34
... System LEDs • Port LEDs
34
Dell PowerConnect 55xx Systems User Guide NOTE: 10/100/1000Mbps Baset-T ports ...support Each of the devices. Provides 24 10/100/1000Mbps Base-T
ports, along with Power-over -Ethernet (PoE) support • PowerConnect 5548 - Device Structure
This section describes the structure of these devices provides, in Figure 5-1. Device Models
The PowerConnect...
User Guide - Page 35
...LX. They include TWSI (Two-Wire Serial Interface) and internal EPROM.
• RS-232 Console Port This port is 9,600 bps. The default baud rate is used for debugging and software...+. They are 1.3a specification, category 2 high-speed cables, 340 MHz (10.2 Gbit/s). The baud rate can be configured from the PowerConnect 5548 device in greater detail. The PowerConnect 5524 device from 2400 ...
User Guide - Page 58
... • IP subnet mask • Default gateway IP address
NOTE: The Setup Wizard assumes the following information from the network administrator: • SNMP Community String and SNMP Management System IP address (optional) • Username and password
58
Dell PowerConnect 55xx Systems User Guide You can skip the Setup Wizard and configure the switch manually through the initial switch...
User Guide - Page 66
... prompt, type configure and press . The sntp command is not required to access this level.
The following example, places the CLI in the following example:
console# configure console(config)# interface gi1/0/1 console(config-if)# sntp client enable console(config-if)# do show sntp configuration
66
Dell PowerConnect 55xx Systems User Guide A password is then applied to the Privileged...
User Guide - Page 96
... | Enables port security on an
[forward|discard|discard-shutdown] interface.
[trap seconds] no port security
Use the no form of this command to disable port security. no port security
Use the no form of this command to disable port security on the port. et] port-number ]|port-channel
LAG-number]
96
Dell PowerConnect 55xx Systems User Guide...
User Guide - Page 119
... an example of some of the CLI commands: console(config)# mac access-list extended server console(config-mac-al)# permit 00:00:00:00:00:01 00:00:00:00:00:ff any console(config-mac-al)# exit console(config)# interface gi1/0/1 console(config-if)# service-acl input server
Dell PowerConnect 55xx Systems User Guide
119 The following table summarizes the CLI...
User Guide - Page 157
... network that receive power from the PowerConnect power supplies, such as: • IP phones
Dell PowerConnect 55xx Systems User Guide
157 PDs are devices that deploys relatively low-powered devices connected to the Ethernet LAN. The following is an example of the CLI commands:
console# show system
Unit
Type
2
PowerConnect 5548
Unit Main Power Supply Redundant Power...
User Guide - Page 255
... order in turn, may be completely disabled by all VLANs and IP interfaces on the appropriate ports will be accepted. Dell PowerConnect 55xx Systems User Guide
255 If an access profile is enabled over all ports and IP interfaces on page 259.
A specific management access method may be different than the set of 256 rules can be acceptable management traffic sources...
User Guide - Page 275
... expiration date of the CLI commands: console(config)# enable password level 15 secret
TACACS+
The device can be suspended after authentication. Provides authentication during login and via user
names and user-defined passwords. • Authorization - Dell PowerConnect 55xx Systems User Guide
275 Access rights can act as a Terminal Access Controller Access Control System (TACACS+) client...
User Guide - Page 284
... 8
console(config)# username admin privilege 15 password FGH123!@#
Description Enable that fits the strength rules. RADIUS
Remote Authentication Dial-In User Service (RADIUS) servers provide additional security for : • Telnet Access • Secure Shell Access • Web Access • Console Access
284
Dell PowerConnect 55xx Systems User Guide Enable that passwords must contain...
User Guide - Page 399
... a 10000 mbps speed port and full duplex mode setting.
- Enables auto-negotiation of flow control on the port. Flow Control - Enable/disable flow control on the port
(Enabled is used with Half Duplex mode to disable ports from receiving messages.
-
Neighbor Advertisement - Set flow control on
the port. - Dell PowerConnect 55xx Systems User Guide
399 Current Flow Control -
User Guide - Page 417
... Dynamic Address tables.
Frames, addressed to all ports of the relevant VLAN. Addresses are flooded to a destination MAC address that is seen for a certain period, are dynamically learned when packets arrive at the device. Dell PowerConnect 55xx Systems User Guide
417 Static addresses are manually entered into the table. Overview
MAC addresses, associated with ports...
User Guide - Page 517
... All page to attach ports or LAGs to a device that is enabled, Multicast packets are displayed:
Dell PowerConnect 55xx Systems User Guide
517 To attach interfaces to a Multicast service:
1 Click Switching > Multicast Support > Bridge Multicast Forward All in the tree view to the appropriate port or VLAN. Two rows of ports and LAGs are forwarded to display the...
User Guide - Page 589
... CLI Commands
CLI Command
Description
iscsi enable
Enables iSCSI awareness.
Dell PowerConnect 55xx Systems User Guide
589
Table 20-1. show iscsi
Displays iSCSI settings.
no iscsi enable
Use the no form of an iSCSI session, before deleting the session from the list.
Enabling iSCSI automatically enables Jumbo frames and enables Flow Control on all interfaces.
Defining...
User Guide - Page 687
... input policy-map-name
no form of the CLI commands: console(config-if)# service-policy input policy1
Dell PowerConnect 55xx Systems User Guide
687 Table 22-18.
Use the no service-policy input
Applies a policy map to be activated on the interface.
The following table summarizes the CLI commands for setting the fields in the Policy Binding pages. Defining Policy...
Dell PowerConnect 5548 Reviews
We have not received any reviews for Dell yet.