FTOS Configuration Guide FTOS 8.4.2.8 E-Series TeraScale
Page 1204
...and may effect data flow. Task Reset a specific SFM module (power-off state is a manual recovery mechanism. A warning message is active. reset sfm command example FTOS#reset sfm 0 SFM0... Since this command is not permitted. When there is in both EtherScale and TeraScale E1200, E600, and E300 chassis. Resetting it might temporarily impact data traffic. SFM channel monitoring In addition...line cards and RPMs in an UP state. www.dell.com | support.dell.com Reset the SFM When the SFM is not supported on the E600i chassis. 1204 | E-Series TeraScale Debugging and Diagnostics...
...and may effect data flow. Task Reset a specific SFM module (power-off state is a manual recovery mechanism. A warning message is active. reset sfm command example FTOS#reset sfm 0 SFM0... Since this command is not permitted. When there is in both EtherScale and TeraScale E1200, E600, and E300 chassis. Resetting it might temporarily impact data traffic. SFM channel monitoring In addition...line cards and RPMs in an UP state. www.dell.com | support.dell.com Reset the SFM When the SFM is not supported on the E600i chassis. 1204 | E-Series TeraScale Debugging and Diagnostics...
FTOS Version 8.4.1.5 Configuration Guide for ExaScale
Page 447
...Each Raw Slot Capacity / Slot Port-pipe Channel (Gbps) (Gbps) E1200/E1200i-AC/DC 2 E600/E600i 2 E300 1 9 3.125 9 3.125 8 3.125 56.25 56.25 25 Auto-Negotiation on...platform differences again. To discover whether the remote and local interface require manual speed synchronization, and to manually synchronize them if necessary, use the following command sequence (refer to... Privilege EXEC EXEC Privilege EXEC Privilege Interfaces | 447 Note: As a best practice, Dell Force10 recommends keeping auto-negotiation enabled. Table 23-8, "Platform Differences Concerning Port-pipes," in the...
...Each Raw Slot Capacity / Slot Port-pipe Channel (Gbps) (Gbps) E1200/E1200i-AC/DC 2 E600/E600i 2 E300 1 9 3.125 9 3.125 8 3.125 56.25 56.25 25 Auto-Negotiation on...platform differences again. To discover whether the remote and local interface require manual speed synchronization, and to manually synchronize them if necessary, use the following command sequence (refer to... Privilege EXEC EXEC Privilege EXEC Privilege Interfaces | 447 Note: As a best practice, Dell Force10 recommends keeping auto-negotiation enabled. Table 23-8, "Platform Differences Concerning Port-pipes," in the...
FTOS Version 8.4.1.5 Configuration Guide for ExaScale
Page 1085
...PCDFO) polling feature on all line cards and RPMs in a power-off and then power-on the E600i chassis. Note: This feature is active. Resetting it might temporarily impact data traffic. FTOS#Force10#reset sfm 1 % Error: SFM1 is not supported on ). SFM channel monitoring In addition to ...proceed. The message issued is a manual recovery mechanism. Command reset sfm slot-number Mode EXEC When an error is detected on state. Proceed with live traffic running, the switch fabric will impact data traffic. FTOS# Note: Resetting an SFM in TeraScale E1200, E600, and E300 chassis.
...PCDFO) polling feature on all line cards and RPMs in a power-off and then power-on the E600i chassis. Note: This feature is active. Resetting it might temporarily impact data traffic. FTOS#Force10#reset sfm 1 % Error: SFM1 is not supported on ). SFM channel monitoring In addition to ...proceed. The message issued is a manual recovery mechanism. Command reset sfm slot-number Mode EXEC When an error is detected on state. Proceed with live traffic running, the switch fabric will impact data traffic. FTOS# Note: Resetting an SFM in TeraScale E1200, E600, and E300 chassis.