D-Link DGS-3427 - xStack Switch - Stackable Support and Manuals
Get Help and Manuals for this D-Link item
View All Support Options Below
Free D-Link DGS-3427 manuals!
Problems with D-Link DGS-3427?
Ask a Question
Free D-Link DGS-3427 manuals!
Problems with D-Link DGS-3427?
Ask a Question
Most Recent D-Link DGS-3427 Questions
D-link Xstak Dgs3427
I changed my swicth configuration accidentally to dhcp mode and now i cant even locate it to enter....
I changed my swicth configuration accidentally to dhcp mode and now i cant even locate it to enter....
(Posted by deudijoao 11 years ago)
Popular D-Link DGS-3427 Manual Pages
Product Manual - Page 3
...Host...36 System Log Save Mode Settings...38 System Log Source Interface Settings...39 System Severity Settings...39 Command Logging Settings...40 SNTP Settings ...40 Time Settings ...40 Time Zone and DST...41 MAC Notification Settings ...44 TFTP Services...44
Global Settings ...44 Port Settings...44 Multiple Image Services ...46 Firmware Information ...46 Config Firmware Image ...47 RCP ...48 RCP...
Product Manual - Page 23
... changed, read the introduction of the xStack® DGS-3400 Series CLI Manual. NOTE: The Switch's factory default IP address is installed on which it through the Ethernet. IP Address
The IP Address may leave the default address (0.0.0.0) in the Administration folder. To change IP settings using the console interface prior to connecting to the...
Product Manual - Page 24
xStack® DGS-3400 Series Layer 2 Gigabit Ethernet Managed Switch
Parameter BOOTP
DHCP
Manual IP Address Subnet Mask
Default Gateway VLAN Name
Description
The Switch will send out a BOOTP broadcast request when it is powered up . The BOOTP protocol allows IP addresses, network masks, and default gateways to the Switch must be assigned by a central BOOTP...
Product Manual - Page 30
... router to use a stateful autoconfiguration process to implement the changes.
Stacking
From firmware release v2.00 of this method, data transfer is only possible in one ...link format. Using this Switch, the xStack® DGS-3400 series now supports switch stacking, where a set the minimum interval time between 4 and 1800 seconds with a default setting of the MaxRtrAdvInterval. The...
Product Manual - Page 31
...DGS-3427 support stacking. If both Primary and Backup masters fail, or are the same. xStack® DGS-3400 Series Layer 2 Gigabit Ethernet Managed Switch
Figure 2 - 9 Switches stacked in a Duplex Ring Figure 2 - 10 Switches stacked in a Duplex Chain
Within each switch plays a role in the Switch.... The Primary Master can be manually set by the user per individual Switch, or if desired, can be...
Product Manual - Page 53
... the Switch to the Switch. Switch configuration settings can be saved and a history and attack log can also be upgraded by transferring a new firmware file from a TFTP server to the TFTP server. Select a port or group of ports on the Switch, configure the following parameters may be uploaded from a TFTP server. xStack® DGS-3400 Series Layer 2 Gigabit...
Product Manual - Page 54
... Config Firmware Image window (Administration > Multiple Image Services > Config Firmware Image). The default Switch settings will download the firmware to the Boot Up Image ID, depending on the TFTP server. Enter the IP address of Image 1 or 2 by the user.
Enter the IP address of the configuration. xStack® DGS-3400 Series Layer 2 Gigabit Ethernet Managed Switch
supports dual...
Product Manual - Page 56
... user. Boot Up files are five ways firmware may read "Anonymous" or "Unknown" for the Switch. If the IP address has this letter attached to the Switch. This field may be the boot up firmware for use.
States the specific time the firmware version was downloaded to it, it denotes a firmware upgrade through Telnet. To view this letter...
Product Manual - Page 127
... not support SIM. There are some advantages in the same IP subnet (broadcast domain). SIM grouping has no limit to the number of SIM groups in your topology options when using other stacking technology. The xStack® DGS-3400 Series switch may join the SIM group of the xStack® DGS-3400 Series switch by manually...
Product Manual - Page 128
... which other switches in the group, including the CS, do not belong. This version will support switch upload and downloads for connections that previously set SIM members... includes new features for firmware, configuration files and log files, as follows: Firmware - Log - xStack® DGS-3400 Series Layer 2 Gigabit Ethernet Managed Switch
• The user can manually configure a CS to ...
Product Manual - Page 138
... specified by Port (port on the CS where the MS resides), MAC Address, Model Name and Version. To update the firmware, enter the Server IP Address where the firmware resides and enter the Path/Filename of the firmware. To specify a certain Switch for upgrading configuration files, click its corresponding check box under the Port heading.
Figure 2 - 157...
Product Manual - Page 219
xStack® DGS-3400 Series Layer 2 Gigabit Ethernet Managed Switch
Q-in-Q
Q-in -Q function on the Switch. Customer's VLAN IDs are segregated within the service provider's network even when they enter the service provider's network, and then removing the tags when the frames leave the network. Customers of a service provider may have different or specific requirements regarding their ...
Product Manual - Page 262
...setting.
xStack® DGS-3400 Series Layer 2 Gigabit Ethernet Managed Switch
Priority (0-7)
Group ID (1-4) Offset
This parameter is specified to re-write the 802.1p default priority previously set specific... this option to instruct the Switch to replace the DSCP value (in the ACL Flow Meter function, the Counter will instruct the Switch to the specified CoS queue. Replace DSCP (063)
...
Product Manual - Page 397
... to save the configuration file indexed as Image file 2. xStack® DGS-3400 Series Layer 2 Gigabit Ethernet Managed Switch Click the No radio button for configuration it must be
designated as the Boot configuration using the Config Current Setting menu (Save Services > Config Current Setting) • Save Log to save only the current log. •...
Product Manual - Page 399
... firmware image for current use.
This firmware will upload this Configuration file for the Switch unless specified here.
• Active - Select this option to set as the file to be configured using the pull-down menu. Click Apply to be stored in the Switch as shown below.
To view this window, click Save Services > Current Configuration Settings...
D-Link DGS-3427 Reviews
We have not received any reviews for D-Link yet.