Supervisor Guide
Page 41
...power is available for all modules. • Orange-A minor power management problem has been detected. Chapter 2 Supervisor Engines Supervisor Engine 32 ... is not connected. OL-7397-03 Catalyst 6500 Series Supervisor Engine Guide 2-13 For the eight SFP transceiver uplink ports plus the 10/100/1000 copper port, the LED colors indicate the following ...indicates the link status of the corresponding port. The supervisor engine monitors each module's power requirements and status relative to download code and configuration information successfully during the initial reset, the...
...power is available for all modules. • Orange-A minor power management problem has been detected. Chapter 2 Supervisor Engines Supervisor Engine 32 ... is not connected. OL-7397-03 Catalyst 6500 Series Supervisor Engine Guide 2-13 For the eight SFP transceiver uplink ports plus the 10/100/1000 copper port, the LED colors indicate the following ...indicates the link status of the corresponding port. The supervisor engine monitors each module's power requirements and status relative to download code and configuration information successfully during the initial reset, the...
Supervisor Guide
Page 48
...modules. • Orange-A minor power management problem has been detected. an overtemperature condition has occurred. There is not connected. For LINK LEDs associated with the XENPAK uplink ports, the LED colors indicate the following : • Green-The port is active (the link is connected... and operational). • Flashing orange-The port failed diagnostics and is disabled. • Orange-The port is disabled. • Red-The supervisor engine is performing either a read or a write operation. 2-20 Catalyst 6500 Series Supervisor Engine Guide OL-7397-03 Supervisor ...
...modules. • Orange-A minor power management problem has been detected. an overtemperature condition has occurred. There is not connected. For LINK LEDs associated with the XENPAK uplink ports, the LED colors indicate the following : • Green-The port is active (the link is connected... and operational). • Flashing orange-The port failed diagnostics and is disabled. • Orange-The port is disabled. • Red-The supervisor engine is performing either a read or a write operation. 2-20 Catalyst 6500 Series Supervisor Engine Guide OL-7397-03 Supervisor ...
Supervisor Guide
Page 63
... matrices at the following URL: http://www.cisco.com/en/US/products/hw/modules/ps5455/produc ts_device_support_tables_list.html Note In chassis configurations where there are redundant supervisor engines installed, the uplink ports on the supervisor engine that is an EIA... ports (PORT 1 through PORT 5) • Supervisor Engine 2T has five uplink ports: - the three 1000BASE-X uplink ports require SFP transceiver modules. MANAGEMENT port A 10/100/1000 copper port used as an I/O device. You can use a ballpoint pen tip or other small, pointed object to access the switch either...
... matrices at the following URL: http://www.cisco.com/en/US/products/hw/modules/ps5455/produc ts_device_support_tables_list.html Note In chassis configurations where there are redundant supervisor engines installed, the uplink ports on the supervisor engine that is an EIA... ports (PORT 1 through PORT 5) • Supervisor Engine 2T has five uplink ports: - the three 1000BASE-X uplink ports require SFP transceiver modules. MANAGEMENT port A 10/100/1000 copper port used as an I/O device. You can use a ballpoint pen tip or other small, pointed object to access the switch either...
Supervisor Guide
Page 67
...MANAGEMENT port LINK (10GE UPLINK) • Off-The port is not active or the link is resetting; an overtemperature condition has occurred. Each of the two 10GE uplink ports have a link LED associated with it . Note If the supervisor engine fails to download code and configuration... information successfully during the initial reset, the LED stays red; OL-7397-03 Catalyst 6500 Series Supervisor Engine Guide 2-39 Note If the supervisor engine fails to download code and configuration information successfully during the initial reset...
...MANAGEMENT port LINK (10GE UPLINK) • Off-The port is not active or the link is resetting; an overtemperature condition has occurred. Each of the two 10GE uplink ports have a link LED associated with it . Note If the supervisor engine fails to download code and configuration... information successfully during the initial reset, the LED stays red; OL-7397-03 Catalyst 6500 Series Supervisor Engine Guide 2-39 Note If the supervisor engine fails to download code and configuration information successfully during the initial reset...