Cisco NME-16ES-1G Support Question
Cisco NME-16ES-1G Support Question
Find answers below for this question about Cisco NME-16ES-1G - Etherswitch Service Mod 16.Need a Cisco NME-16ES-1G manual? We have 1 online manual for this item!
Question posted by mmsundara on April 26th, 2010
How To Resolve Port Suspended Issue On Nme-16es-1g?
Cisco NME (NME-16-ES-1G) card fatst ethernet port goes down after soem idel tiem. due to this the port goes to suspended state
Current Answers
Related Cisco NME-16ES-1G Manual Pages
User Guide - Page 1
... (including Layer 2/Layer 3 CoS/DSCP mapping and rate limiting), security ACL, IGMP snooping, per-port storm control, and fallback bridging support for the 16-
Enhancements were added in Cisco IOS Release 12.2(2)XT and Cisco IOS Release 12.2(8)T and above. 16- and 36-Port Ethernet Switch Module, page 130 • Command Reference, page 157 • Glossary, page 242...
User Guide - Page 2
..., page 25 • Quality of Service, page 29 • Maximum Number of the packet. The Ethernet switch network module is supported on Cisco 2600 series, Cisco 3600 series, and Cisco 3700 series routers. The 16- Feature Overview
16- and 36-Port Ethernet Switch Module for the next packet. The gigabit Ethernet can be used as an uplink port to a server or as a stacking...
User Guide - Page 3
... level of bandwidth, the network performance of all ports connect to a common backplane within the hub, and the bandwidth of seconds, it floods the frame to the hub. so if an address remains inactive for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Feature Overview
The Ethernet switch network module solves congestion problems caused by high...
User Guide - Page 4
... spanning tree for the specific VLAN. Feature Overview
16- The interface will travel on one instance of the other 802.1Q switch.
and 36-Port Ethernet Switch Module for an 802.1Q trunk is the same on both ends of the trunk is maintained by Cisco switches separated by a Cisco switch mark the line as a single trunk link between...
User Guide - Page 5
... administration. and 36-Port Ethernet Switch Module for which you can be configured with a VLAN, but it does not support subinterfaces. The VLAN corresponds to the VLAN tag associated with trunks. Configure a VLAN interface for each VLAN for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Feature Overview
Switch Virtual Interfaces
A switch virtual interface (SVI) represents...
User Guide - Page 6
and 36-Port Ethernet Switch Module for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
VTP Domain A VTP domain (also called a VLAN management domain) ...
16- By default, the switch is in VTP server mode and is specified or learned. If you configure the switch as VTP servers, but the changes affect only the individual switch.
However, in an un-named domain state until the switch ...
User Guide - Page 7
... are version 2-capable. Cisco IOS Release 12.2(2)XT, 12.2(8)T, and 12.2(15)ZJ
7 16- Consistency Checks-In VTP version 2, VLAN consistency checks (such as a switch running VTP version 1, provided...and mode.
Since only one of six EtherChannels. and 36-Port Ethernet Switch Module for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Feature Overview
VTP Version 2 If you use MAC...
User Guide - Page 8
...port. The authentication server authenticates each client connected to a switch port before making available any services offered by itself, make interfaces incompatible for Cisco 2600 Series, Cisco 3600 Series, and Cisco...the interfaces do not form an EtherChannel. Cisco IOS Release 12.2(2)XT, 12.2(8)T, and 12.2(15)ZJ
8 and 36-Port Ethernet Switch Module for the formation of the remaining...
User Guide - Page 9
... client, verifying that information with Ethernet switch network module
• Client-the device (workstation) that offered in the IEEE 802.1x specification.)
Note To resolve Windows XP network connectivity and 802.1x authentication issues, read the Microsoft Knowledge Base article at this release, the Remote Authentication Dial-In User Service (RADIUS) security system with the...
User Guide - Page 40
..., page 41
Configuring the Ethernet Switch Network Module for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Per-Port Storm-Control
A packet storm occurs when a large number of the station attempting to time out. and 36-Port Ethernet Switch Module for Cisco AVVID/IP Telephony The Ethernet switch network module has sixteen 10/100 switched Ethernet ports with multicast, broadcast...
User Guide - Page 41
....2(15)ZJ
41 and 36-Port Ethernet Switch Module for a period of the send and receive keywords with respect to Cisco AVVID: • All switch ports are in access VLAN 1. • All switch ports are static access ports, not 802.1Q trunk ports. • Default voice VLAN is not configured on when a remote port is set port flowcontrol command.
Use send off...
User Guide - Page 53
... the following commands beginning in the VTP domain.
When you delete a VLAN from all switches in privileged EXEC mode:
Cisco IOS Release 12.2(2)XT, 12.2(8)T, and 12.2(15)ZJ
53 16-
and 36-Port Ethernet Switch Module for the different media types: Ethernet VLAN 1 and FDDI or Token Ring VLANs 1002 to privileged EXEC mode. Adds an...
User Guide - Page 59
...
Configures EtherChannel load balancing.
stand-alone s - Layer3
S - Exits configuration mode. suspended
R - Layer2
U -
Step 1 Use the show etherchannel summary
Flags: D - Exits configuration mode. down
P - and 36-Port Ethernet Switch Module for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Configuration Tasks
Removing an Interface from an EtherChannel
To...
User Guide - Page 100
Distributed Fast Switched
H - Configuration Tasks
16- and 36-Port Ethernet Switch Module for an IP PIM Layer 3 interface:
Step 1 Router# show ip pim interface count
Step 2
State:* - The...to verify IP multicast Layer 3 switching information for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Verifying IP Multicast Layer 3 Hardware Switching Summary
Note The show ip mroute...
User Guide - Page 107
....2(2)XT, 12.2(8)T, and 12.2(15)ZJ
107 User priority bits in designing Cisco AVVID networks.
16- This is a vital component in the 802.1p portion of Cisco IOS software for example, interface fa5/1).
The Ethernet switch network module provides the performance and intelligent services of the 802.1Q standard header are enforced using Layer 2 and 3 information...
User Guide - Page 110
... to the Switch
You can use the following topics are issued.
The following commands beginning in advance with a database of its assigned IP address. and 36-Port Ethernet Switch Module for each member switch must be ...command to verify that the IP information is saved when the switch is saved in privileged EXEC mode.
110
Cisco IOS Release 12.2(2)XT, 12.2(8)T, and 12.2(15)ZJ Router(...
User Guide - Page 120
...ports support only CEF switching (IP fast switching is in Layer 2 mode (the default), you enter a VLAN ID following procedure shows how to an interface.
Configuration Tasks
16- Note If the physical port...any VLANs for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Configuring Layer 3 Interfaces
The Ethernet switch network module supports two types of routed ports and SVIs ...
User Guide - Page 138
... example shows CDP counter configuration being enabled on the NM-16ESW:
Router# clear cdp counters
138
Cisco IOS Release 12.2(2)XT, 12.2(8)T, and 12.2(15)ZJ 16-
and 36-Port Ethernet Switch Module for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Configuration Examples for VLAN 10, with a network diameter of 4:
Router# configure terminal Router(config...
User Guide - Page 151
and 36-Port Ethernet Switch Module for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Configuration Examples for the 16- Switch(config)# interface gigabitethernet4/0 Switch(config-if)# flowcontrol receive on Switch(config-if)# end
The following example shows flow control configuration being verified:
Switch# show interface gigabitethernet4/0 GigabitEthernet4/0 is up, line ...
User Guide - Page 244
... and service availability.
Ability to travel securely over an IP-based internet with ABR, CBR, and UBR. These voice packets are extremely flexible. Enables IP traffic to carry normal telephony-style voice over a public TCP/IP network by creating a spanning tree. and 36-Port Ethernet Switch Module for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700...
Similar Questions
Cisco Nme-x-23es-1g Initial Configuration
Following instructions in Cisco online docs. I set the ip address for gi 1/0 and attempt to connect ...
Following instructions in Cisco online docs. I set the ip address for gi 1/0 and attempt to connect ...
(Posted by droberts4 11 years ago)
Nme-x-23es-1g Initial Configuration
I am unable to contact the module: GW12#service-module gi 1/0 session % telnet connections not per...
I am unable to contact the module: GW12#service-module gi 1/0 session % telnet connections not per...
(Posted by droberts4 11 years ago)
How I Should Real On A Switch Device/slot/port Who Is Who
I have some switches in stack fasion and other as single switch and the way to name the interfaces i...
I have some switches in stack fasion and other as single switch and the way to name the interfaces i...
(Posted by JEPA 11 years ago)
How Do I Set Poe Of 24 Ports,15.4w Or 48 Of 7.7w In The 48ps Model? Any Default?
How do I set PoE of 24 ports,15.4W or 48 of 7.7W in the 48PS model? Any default?
How do I set PoE of 24 ports,15.4W or 48 of 7.7W in the 48PS model? Any default?
(Posted by rebeca 11 years ago)
Nme-16es-1g, All Port Status Leds Are Green. Even Ones Not Cabled To Anything.
I have come across two NME-16ES-1G switch modules that all port status leds are green.. Even ones no...
I have come across two NME-16ES-1G switch modules that all port status leds are green.. Even ones no...
(Posted by ccasario 13 years ago)