Supervisor Guide
Page 41
... port failed diagnostics and is disabled. • Orange-The port is disabled. • Red-The supervisor engine is performing either a read or a write operation. OL-7397-03 Catalyst 6500...indicates the link status of the corresponding port. There is available for all modules. • Orange-A minor power management problem has been detected. an overtemperature ...self-diagnostics. • Green-Power management is functioning normally and sufficient power is insufficient power for all modules to download code and configuration information successfully during the initial reset...
... port failed diagnostics and is disabled. • Orange-The port is disabled. • Red-The supervisor engine is performing either a read or a write operation. OL-7397-03 Catalyst 6500...indicates the link status of the corresponding port. There is available for all modules. • Orange-A minor power management problem has been detected. an overtemperature ...self-diagnostics. • Green-Power management is functioning normally and sufficient power is insufficient power for all modules to download code and configuration information successfully during the initial reset...
Supervisor Guide
Page 48
... DISK 0 (PCMCIA) LED Off-The port is not active or the link is performing either a read or a write operation. 2-20 Catalyst 6500 Series Supervisor Engine Guide OL-7397-03 running self-diagnostics. • Green-Power management is functioning normally and sufficient power is ... port socket is empty (no XENPAK transceiver is installed) or the XENPAK transceiver is available for all modules. • Orange-A minor power management problem has been detected. The supervisor engine monitors each module's power requirements and status relative to download code and configuration ...
... DISK 0 (PCMCIA) LED Off-The port is not active or the link is performing either a read or a write operation. 2-20 Catalyst 6500 Series Supervisor Engine Guide OL-7397-03 running self-diagnostics. • Green-Power management is functioning normally and sufficient power is ... port socket is empty (no XENPAK transceiver is installed) or the XENPAK transceiver is available for all modules. • Orange-A minor power management problem has been detected. The supervisor engine monitors each module's power requirements and status relative to download code and configuration ...
Supervisor Guide
Page 63
...USB port is located on the supervisor engine that is port used for a list of the switch. For X2 and SFP transceiver support, refer to each slot. Universal Serial Bus (USB) Two USB 2.0 ports are not equipped with hardware flow control. MANAGEMENT port A 10/100/1000 copper port ...to the compatibility matrices at the following URL: http://www.cisco.com/en/US/products/hw/modules/ps5455/produc ts_device_support_tables_list.html Note In chassis configurations where there are fully functional. • Each uplink port has a link LED associated with it . The PCMCIA slot...
...USB port is located on the supervisor engine that is port used for a list of the switch. For X2 and SFP transceiver support, refer to each slot. Universal Serial Bus (USB) Two USB 2.0 ports are not equipped with hardware flow control. MANAGEMENT port A 10/100/1000 copper port ...to the compatibility matrices at the following URL: http://www.cisco.com/en/US/products/hw/modules/ps5455/produc ts_device_support_tables_list.html Note In chassis configurations where there are fully functional. • Each uplink port has a link LED associated with it . The PCMCIA slot...
Supervisor Guide
Page 67
...-03 Catalyst 6500 Series Supervisor Engine Guide 2-39 an overtemperature condition has occurred. MANAGEMENT port LINK (10GE UPLINK) • Off-The port is not active or the link is not connected. Each of the two 10GE uplink ports have a link LED associated with it . Note If the supervisor engine fails to download code and configuration information...
...-03 Catalyst 6500 Series Supervisor Engine Guide 2-39 an overtemperature condition has occurred. MANAGEMENT port LINK (10GE UPLINK) • Off-The port is not active or the link is not connected. Each of the two 10GE uplink ports have a link LED associated with it . Note If the supervisor engine fails to download code and configuration information...