Users Manual - English
Page 103
Make sure that the Drum LED is red. Caution ■ The Drum LED indication does not disappear until you reset the drum counter. ■ Do not reset the drum counter when you replace only the toner cartridge. 8 Close the front cover. 9 Make sure that the printer is turned on, the front cover is open and the Status LED is now off. Figure 5-20 7 Reset the drum counter. ROUTINE MAINTENANCE 5 - 11 6 Put the drum unit assembly in the printer. See the instructions supplied with the new drum unit.
Make sure that the Drum LED is red. Caution ■ The Drum LED indication does not disappear until you reset the drum counter. ■ Do not reset the drum counter when you replace only the toner cartridge. 8 Close the front cover. 9 Make sure that the printer is turned on, the front cover is open and the Status LED is now off. Figure 5-20 7 Reset the drum counter. ROUTINE MAINTENANCE 5 - 11 6 Put the drum unit assembly in the printer. See the instructions supplied with the new drum unit.
Service Manual
Page 69
...default factory settings. NOTE: *If you turn on APIPA, see the Network User's Guide or visit http://solutions.brother.com 2-36 Active LED is yellow: The Active LED will start warming up. Keep the Go button pressed ...down the Go button until all the LEDs light up . When the Drum, Paper and Status LEDs go off. CHAPTER 2 INSTALLATION AND BASIC OPERATION 6. All the LEDs will be green if... print server is receiving or transmitting data. 6.2 Network Factory default setting (For HL-5170DN) If you wish to reset the print server back to the network.
...default factory settings. NOTE: *If you turn on APIPA, see the Network User's Guide or visit http://solutions.brother.com 2-36 Active LED is yellow: The Active LED will start warming up. Keep the Go button pressed ...down the Go button until all the LEDs light up . When the Drum, Paper and Status LEDs go off. CHAPTER 2 INSTALLATION AND BASIC OPERATION 6. All the LEDs will be green if... print server is receiving or transmitting data. 6.2 Network Factory default setting (For HL-5170DN) If you wish to reset the print server back to the network.
Service Manual
Page 174
... fit the toner cartridge properly, or it lock into the printer. When the toner cartridge is installed correctly, the blue lock lever is red. (7) To reset the drum counter, press and hold down the Go button until you hear it may be damaged. • Handle the... tightly so that toner powder does not spill out of the drum unit assembly. (Fig.5-4) HL-5130/5140/5150D/5170DN SERVICE MANUAL (4) Unpack the new drum unit. (5) Put the toner cartridge in the new drum unit until all four LEDs are lit, release the Go button. (8) Close the front cover. (9) Make sure that the printer...
... fit the toner cartridge properly, or it lock into the printer. When the toner cartridge is installed correctly, the blue lock lever is red. (7) To reset the drum counter, press and hold down the Go button until you hear it may be damaged. • Handle the... tightly so that toner powder does not spill out of the drum unit assembly. (Fig.5-4) HL-5130/5140/5150D/5170DN SERVICE MANUAL (4) Unpack the new drum unit. (5) Put the toner cartridge in the new drum unit until all four LEDs are lit, release the Go button. (8) Close the front cover. (9) Make sure that the printer...
Service Manual
Page 192
...empty Cover open (Front cover) Cover open (Jam clear cover) Paper jam No paper (HL-5130) No paper (HL5140/5150D/5170 DN) No tray 1 Manual feed Memory full Print overrun Clean drum unit Toner (Yellow light) LED Drum (Yellow light) Paper (Yellow blink) Status (Red light)) Remedy Replace the toner cartridge... action described for HL5130.) Set the paper on the LEDs is user recoverable. Press the go button. (Error message is to be necessary to reset the printer with a new one. Press the go button. (Error message is displayed.) Press the go button. Load paper into the printer....
...empty Cover open (Front cover) Cover open (Jam clear cover) Paper jam No paper (HL-5130) No paper (HL5140/5150D/5170 DN) No tray 1 Manual feed Memory full Print overrun Clean drum unit Toner (Yellow light) LED Drum (Yellow light) Paper (Yellow blink) Status (Red light)) Remedy Replace the toner cartridge... action described for HL5130.) Set the paper on the LEDs is user recoverable. Press the go button. (Error message is to be necessary to reset the printer with a new one. Press the go button. (Error message is displayed.) Press the go button. Load paper into the printer....
Service Manual
Page 244
... in this chapter (PIT3). The printer prints a list of mode Test Sample Page Drum Paper Print Fonts (HL-5140/5150D/5170DN only) Factory Reset Status Network factory reset (yellow) (APIPA: ON) Status Network factory reset (green) (APIPA: OFF) Function The printer prints a test sample page. The ...reset to its factory setting. (APIPA is OFF) Refer to use following the steps below . Select the test mode you want to Section 6.2 of Chapter 2. The network setting is reset to its factory setting. (APIPA is ON) Refer to Section 6.2 of Chapter 2. 7-1 LED Toner Type of the internal...
... in this chapter (PIT3). The printer prints a list of mode Test Sample Page Drum Paper Print Fonts (HL-5140/5150D/5170DN only) Factory Reset Status Network factory reset (yellow) (APIPA: ON) Status Network factory reset (green) (APIPA: OFF) Function The printer prints a test sample page. The ...reset to its factory setting. (APIPA is OFF) Refer to use following the steps below . Select the test mode you want to Section 6.2 of Chapter 2. The network setting is reset to its factory setting. (APIPA is ON) Refer to Section 6.2 of Chapter 2. 7-1 LED Toner Type of the internal...
Service Manual
Page 257
... is switched to 400V again when the toner cartridge is switched from the drum unit life.) The developing bias is replaced following settings, the developing bias reset function operates. 1. This function helps a counter reset for the main items to 300V when 7,000 pages are as follows;... Install the drum unit into the printer. 4. Press the "GO" switch again when keeping the front ...
... is switched to 400V again when the toner cartridge is switched from the drum unit life.) The developing bias is replaced following settings, the developing bias reset function operates. 1. This function helps a counter reset for the main items to 300V when 7,000 pages are as follows;... Install the drum unit into the printer. 4. Press the "GO" switch again when keeping the front ...