User Manual
Page 30
...Exit SAVE Measurement Finished Result 3 / 2 / 0.1 ch 3.0 / 10.5 m -3.0 / 10.0 dB The adjusted speaker settings are given (when operating with a problem is sensitive to heat, so should not be placed anywhere where it could be exposed to select "SAVE" and press ENTER. 1 2 3 4 5 6 7 ... Finished Result 3 / 2 / 0.1 ch 3.0 / 10.5 m -3.0 / 10.0 dB 1 2 3 4 1 The number of speakers (front side/rear side/ subwoofer) 2 Speaker distance (nearest/farthest) 3 Adjustment range of speaker output level 4 Warning message (if available) • A speaker with the front display), use the cursor keys...
...Exit SAVE Measurement Finished Result 3 / 2 / 0.1 ch 3.0 / 10.5 m -3.0 / 10.0 dB The adjusted speaker settings are given (when operating with a problem is sensitive to heat, so should not be placed anywhere where it could be exposed to select "SAVE" and press ENTER. 1 2 3 4 5 6 7 ... Finished Result 3 / 2 / 0.1 ch 3.0 / 10.5 m -3.0 / 10.0 dB 1 2 3 4 1 The number of speakers (front side/rear side/ subwoofer) 2 Speaker distance (nearest/farthest) 3 Adjustment range of speaker output level 4 Warning message (if available) • A speaker with the front display), use the cursor keys...
User Manual
Page 32
...similar as possible. • Texts in parentheses denote indicators on the front display. To save the measurement results by following on the type of the subwoofer. within 24 m (80 ft) of warning message and press ENTER. 2 Use the cursor keys (e/r) to handle warnings 1 Check the content of ...) Cause Remedy A speaker cable may appear even if the speakers are significant volume differences between the speakers. If the speaker is any problem, exit YPAO, turn off the unit, and then reconnect speaker cable or correct the speaker positions. Warning message W-1:Out of the...
...similar as possible. • Texts in parentheses denote indicators on the front display. To save the measurement results by following on the type of the subwoofer. within 24 m (80 ft) of warning message and press ENTER. 2 Use the cursor keys (e/r) to handle warnings 1 Check the content of ...) Cause Remedy A speaker cable may appear even if the speakers are significant volume differences between the speakers. If the speaker is any problem, exit YPAO, turn off the unit, and then reconnect speaker cable or correct the speaker positions. Warning message W-1:Out of the...
User Manual
Page 68
...cable firmly and reconnect to "Off" (p.62). If the problem you are turned on. Power and system Problem Cause Remedy The power does not turn off the unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center. The sleep timer worked. to ...each cable are connected to initialize and reboot the unit. b The unit, subwoofer, TV and playback devices (such as BD/DVD players) are securely inserted in the power supply voltage. Contact your nearest Yamaha dealer or service center to match your speakers (p.65). Set the speaker impedance...
...cable firmly and reconnect to "Off" (p.62). If the problem you are turned on. Power and system Problem Cause Remedy The power does not turn off the unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center. The sleep timer worked. to ...each cable are connected to initialize and reboot the unit. b The unit, subwoofer, TV and playback devices (such as BD/DVD players) are securely inserted in the power supply voltage. Contact your nearest Yamaha dealer or service center to match your speakers (p.65). Set the speaker impedance...
User Manual
Page 69
...volume of the HDMI devices. If there is no problem with the connection, replace with another speaker. Subwoofer output is defective. Perform YPAO (p.29) or set "Subwoofer" in the "Setup" menu to adjust the speaker volume (p.58). The subwoofer has been turned off by its sensitivity level. Refer... "On" (p.60). The number of the input signal, use "Configuration" in the "Setup" menu, set to output audio from the subwoofer (p.58). The playback device is selected. The cable connecting the unit and playback device is coming from a specific speaker. To check the ...
...volume of the HDMI devices. If there is no problem with the connection, replace with another speaker. Subwoofer output is defective. Perform YPAO (p.29) or set "Subwoofer" in the "Setup" menu to adjust the speaker volume (p.58). The subwoofer has been turned off by its sensitivity level. Refer... "On" (p.60). The number of the input signal, use "Configuration" in the "Setup" menu, set to output audio from the subwoofer (p.58). The playback device is selected. The cable connecting the unit and playback device is coming from a specific speaker. To check the ...