Service Manual
Page 2
...Diagram----------- 47 11.6. A-Board (4/15) Schematic Diagram 51 11.10. A-Board (7/15) Schematic Diagram 54 11.13. A-Board (12/15) Schematic Diagram 59 11.18. A-Board (15/15) Schematic ... 13.1. About lead free solder (PbF 5 3 Service Navigation 6 3.1. Power LED Blinking timing chart 14 6.3. Remove the Side terminal cover and Rear terminal cover 18 7.4. Remove...Discharge (ESD) to enter into Service Mode 9 5.2. Remove the Control button unit 19 7.8. Remove the Plasma panel section from the Cabinet assy (glass 22 7.19. P(P-1)-Board (2/2) Schematic Diagram 45 11.4. A-Board...
...Diagram----------- 47 11.6. A-Board (4/15) Schematic Diagram 51 11.10. A-Board (7/15) Schematic Diagram 54 11.13. A-Board (12/15) Schematic Diagram 59 11.18. A-Board (15/15) Schematic ... 13.1. About lead free solder (PbF 5 3 Service Navigation 6 3.1. Power LED Blinking timing chart 14 6.3. Remove the Side terminal cover and Rear terminal cover 18 7.4. Remove...Discharge (ESD) to enter into Service Mode 9 5.2. Remove the Control button unit 19 7.8. Remove the Plasma panel section from the Cabinet assy (glass 22 7.19. P(P-1)-Board (2/2) Schematic Diagram 45 11.4. A-Board...
Service Manual
Page 11
... Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment will not be cleared by decimal Count : Number of LED blinking) indication. Time : Cumulative power on the remote control. 5.2.2. Exit 1. Service tool mode 5.2.1. Display of SOS History SOS History (Number of ON times by decimal Note...
... Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment will not be cleared by decimal Count : Number of LED blinking) indication. Time : Cumulative power on the remote control. 5.2.2. Exit 1. Service tool mode 5.2.1. Display of SOS History SOS History (Number of ON times by decimal Note...
Service Manual
Page 13
... main unit, press [OK] button on the remote control for more than 3 seconds. 6 Troubleshooting Guide Use the self-check function to factory shipment setting: Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote control for more than 3 seconds. 6.1.2. Self-check indication... Confirm the following parts if NG was displayed. 13 Check of the IIC bus lines 6.1.1. Exit Disconnect the AC cord from wall outlet. 6.1.3. Power LED Blinking timing 6.1. Checking the IIC bus lines 2.
... main unit, press [OK] button on the remote control for more than 3 seconds. 6 Troubleshooting Guide Use the self-check function to factory shipment setting: Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote control for more than 3 seconds. 6.1.2. Self-check indication... Confirm the following parts if NG was displayed. 13 Check of the IIC bus lines 6.1.1. Exit Disconnect the AC cord from wall outlet. 6.1.3. Power LED Blinking timing 6.1. Checking the IIC bus lines 2.
Service Manual
Page 14
Power LED Blinking timing chart 1. Subject Information of the unit. 14 Contents When an abnormality has occurred the unit, the protection circuit operates and reset to the stand by the number of blinks of the Power LED on the front panel of LED Flashing timing chart. 2. At this time, the defective block can be identified by mode. 6.2.
Power LED Blinking timing chart 1. Subject Information of the unit. 14 Contents When an abnormality has occurred the unit, the protection circuit operates and reset to the stand by the number of blinks of the Power LED on the front panel of LED Flashing timing chart. 2. At this time, the defective block can be identified by mode. 6.2.