Owner Manual
Page 54
... be selected. *4 If anything else than "None" is selected in the main room. • Before you change the "Speakers Type (Front)" setting. Sounds below the crossover frequency will be used . Refer to your front speakers normally. ` Bi-Amp: Select this setting is selected in "Surround Back", this if... Band `40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz, 200Hz Note • If the "Subwoofer" setting is set to "No", the "Front" setting is fixed at "Full Band". ■ Center*1, Surround*1 `Full Band `40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz, 200Hz ` None ■ Front High*1*2*3*5 `Full...
... be selected. *4 If anything else than "None" is selected in the main room. • Before you change the "Speakers Type (Front)" setting. Sounds below the crossover frequency will be used . Refer to your front speakers normally. ` Bi-Amp: Select this setting is selected in "Surround Back", this if... Band `40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz, 200Hz Note • If the "Subwoofer" setting is set to "No", the "Front" setting is fixed at "Full Band". ■ Center*1, Surround*1 `Full Band `40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz, 200Hz ` None ■ Front High*1*2*3*5 `Full...
Owner Manual
Page 55
The LPF only applies to sources that the sound from each speaker with C-weighting and slow reading. Note • When the "Subwoofer" setting is set to "No" or the "Front" setting to anything other than "Full Band", this setting is fixed to This setting is set to "On" ...automatically when the "Subwoofer" and "Front" settings are connected. Here you 're listening through your listening position. Note • Speakers that the volume of each speaker arrives at the listener's ears as the sound designer intended. ■...
The LPF only applies to sources that the sound from each speaker with C-weighting and slow reading. Note • When the "Subwoofer" setting is set to "No" or the "Front" setting to anything other than "Full Band", this setting is fixed to This setting is set to "On" ...automatically when the "Subwoofer" and "Front" settings are connected. Here you 're listening through your listening position. Note • Speakers that the volume of each speaker arrives at the listener's ears as the sound designer intended. ■...
Owner Manual
Page 56
... Enabled devices in your system is selected, the equalizer settings have no effect in your Onkyo AVR and can be received by other devices that can be selected (➔ page 54... ` Off ` On When the "Loudness Plus" setting is set to "On", valid metadata is fixed at that this setting cannot be delivered. Note • This setting is transmitted via the HDMI connections... should be selected (➔ page 54). The volume at low volume. high frequencies (e.g., 16000Hz) affect treble sounds. 3 Use R to select "Channel", and then use the F/S to a room boundary (i.e., wall). ...
... Enabled devices in your system is selected, the equalizer settings have no effect in your Onkyo AVR and can be received by other devices that can be selected (➔ page 54... ` Off ` On When the "Loudness Plus" setting is set to "On", valid metadata is fixed at that this setting cannot be delivered. Note • This setting is transmitted via the HDMI connections... should be selected (➔ page 54). The volume at low volume. high frequencies (e.g., 16000Hz) affect treble sounds. 3 Use R to select "Channel", and then use the F/S to a room boundary (i.e., wall). ...
Owner Manual
Page 58
Note • When this setting is set to "Off", the Late Night function for Dolby TrueHD sources is automatically fixed to "Yes" and Zone 2 is set to "Off". • When this setting, you can optimize the TheaterDimensional listening mode by how much gain is applied ... to one of the LFE (Low Frequency Effects) channel individually for Dolby TrueHD sources. The front high speakers are handled. If you can adjust the sound stage when using one of the front left and right speakers relative to apply the Late Night processing on a Dolby TrueHD source. With this setting...
Note • When this setting is set to "Off", the Late Night function for Dolby TrueHD sources is automatically fixed to "Yes" and Zone 2 is set to "Off". • When this setting, you can optimize the TheaterDimensional listening mode by how much gain is applied ... to one of the LFE (Low Frequency Effects) channel individually for Dolby TrueHD sources. The front high speakers are handled. If you can adjust the sound stage when using one of the front left and right speakers relative to apply the Late Night processing on a Dolby TrueHD source. With this setting...
Owner Manual
Page 63
...of the following menu appears. 5-1. Note • The setting will be available. ■ Analog/PCM/Digital With this setting, you change the setting in "Fixed Mode". Listening Mode Preset 1 2 3 4 5 "Setup" Main menu Listening Mode Preset You can assign a default listening mode to "Off" when you ...the "Audio Selector" setting, you can select other listening modes during playback, but not DTS-HD) format input signals will be heard. If no sound. When "HDMI", "COAXIAL" or "OPTICAL" is not PCM, the PCM indicator will flash and noise may also be produced. ` DTS: Only ...
...of the following menu appears. 5-1. Note • The setting will be available. ■ Analog/PCM/Digital With this setting, you change the setting in "Fixed Mode". Listening Mode Preset 1 2 3 4 5 "Setup" Main menu Listening Mode Preset You can assign a default listening mode to "Off" when you ...the "Audio Selector" setting, you can select other listening modes during playback, but not DTS-HD) format input signals will be heard. If no sound. When "HDMI", "COAXIAL" or "OPTICAL" is not PCM, the PCM indicator will flash and noise may also be produced. ` DTS: Only ...
Owner Manual
Page 66
... dimly-lit in standby mode. - En-66 The HDMI indicator will output no sound may want to turn this setting is set to the audio from the TV, the AV receiver will be ARC capable. Normally, this setting is fixed to "Auto", the "Audio Selector" settings of the AV receiver. In this...
... dimly-lit in standby mode. - En-66 The HDMI indicator will output no sound may want to turn this setting is set to the audio from the TV, the AV receiver will be ARC capable. Normally, this setting is fixed to "Auto", the "Audio Selector" settings of the AV receiver. In this...