Netgear SW502 - Switch Support and Manuals
Get Help and Manuals for this Netgear item
View All Support Options Below
Free Netgear SW502 manuals!
Problems with Netgear SW502?
Ask a Question
Free Netgear SW502 manuals!
Problems with Netgear SW502?
Ask a Question
Most Recent Netgear SW502 Questions
Can I Get A Datasheet For The Old Bay Network Switch, Part Number Sw502?
Also what Netgear part number whould you recommend, as a close replacement for the SW502? And will t...
Also what Netgear part number whould you recommend, as a close replacement for the SW502? And will t...
(Posted by ChrisRobinson 12 years ago)
Popular Netgear SW502 Manual Pages
User Manual - Page 2
... that may be contained in this User's Manual, at any inaccuracies that is accurate;
PLANET makes no commitment to update or keep current the information in this User's Manual, and reserves the right to make improvements to this User's Manual and/or to the products described in this manual that may have occurred. Disclaimer
PLANET...
User Manual - Page 3
...
This equipment has been tested and found to comply with the Instruction manual, may cause harmful interference to radio communications. Operation of the FCC Rules. Revision
PLANET Fast Ethernet Switch User's Manual
FOR MODELS: GSD-503/GSD-504/GSD-803/GSD-804
Rev: 1.0(May.2005)
Part No.: 2011-A33160-000
These limits are designed to take...
User Manual - Page 4
...for repair.
1.2 How to Use This Manual
This Fast Ethernet Switch User Manual is structured as follows:
Chapter 2 Installation The chapter explains the feature, functionality and the physical installation of the Fast Ethernet Switch.
1.3 Product Features
fComply with IEEE 802.3, 10Base-T, IEEE 802.3u,
Appendix A This chapter contains cable information of the Switch. Chapter 4 Troubleshooting...
User Manual - Page 5
... fCompact size design for wall mount or desktop placement fHigh performance Store-and-Forward Switching Architecture fRunt and CRC filtering fFlow control (Back Pressure) supports in half-duplex mode f1K MAC Address Table, automatically learning and aging fLED indicators array for easy diagnostic, troubleshooting fPlug-and-Play Installation fAuto-MDI/MDIX on each port
User Manual - Page 6
1.4 Product Specifications
Model
SW-502
SW-802
Hardware Specification
Network Ports
5 10/100Base-T RJ-45 8 10/100Base-T RJ-45
MDI/MDI-X ports
MDI/MDI-X ports
Dimensions (W x D x H) 159 x 100 x 28mm
Weight (KG)
0.16 KG
0.18 KG
Power Requirement
External Power adapter 12V 500 mA
Switch Specification
Switch Architecture
Store-and-forward
Address Table
1K entries, auto learning/...
User Manual - Page 7
... mode of networking is the ideal device for bridging Ethernet to Install and use", "Compact-sized design", and "Simple troubleshooting", PLANET SW-502/SW-802 provides cost-conscious business and home users with its 5/8 ports. The SW 502/SW-802 is a Simple and cost-effective, highly reliable network switch. To segment the network, ease the network traffic, the 5/8-port...
User Manual - Page 8
This product also supports store-and-forward forwarding scheme to 1K different MAC address and enables filtering and forwarding at full wire speed.
2.1.2 Switch Front Panel
Figure 2-1 & 2-2 show the front panel and rear panel of SW-502
Figure 2-1 SW-502 front panel
5
4
3
2
1
Figure 2-2 SW-502 rear panel
Figure 2-3 & 2-4 show the front panel and rear panel of SW-802 With an...
User Manual - Page 9
... link through that port. The device is a power-required device, it means, it will not work till it is powered on.
Blink: indicate that the switch is actively sending or receiving data over that port is successfully established. If your networks should active all the time, please
Figure...
User Manual - Page 10
... the procedures in Chapter 1, Section 1.4 Product Specification.
A. In some area, installing a surge suppression device may also help to protect your Fast Ethernet Switch and make connections to the recessed areas on the bottom of the switch. Note: This switch does not need software configuration.
2.2.1 Desktop Installation
To install the switch on desktop, simply follow the next steps...
User Manual - Page 11
... the power cable to the switch. Connect the power plug of the power cable to a standard wall outlet. For more information, please see the Cabling Specification in Appendix A. Step5: Supply power to the switch requires UTP Category 5 network
cabling with RJ-45 tips. B. Note: Connection to the switch.
A. When the switch receives power, the Power...
User Manual - Page 12
... will be used to the network it will also check the destination address besides the source address learning. This address table composed of the Ethernet Switching, it connected. If not found , and the destination address is located according to all the other related information in network, including MAC address, port no...
User Manual - Page 13
...automatically sets the best possible bandwidth when a The fast forwarding makes the switch attractive for the incoming port and forwards the packet, only if required. An Ethernet Switching can.... Therefore, no error packets occur.
The Switch performs "Store and forward" therefore, no error packets occurrence, it reduces the re-transmission rate.
The Ethernet Switch scans the destination ...
User Manual - Page 15
... Switch.
4.
Please power down to help you solve problems. If Giga Switch is the right type Turn off the power.
Performance is set up...Switch Try another port on the other stations located on the Switch I Make sure the cable is installed properly Make sure the cable is not functioning properly, make sure the Ethernet Switch was set to instructions in this manual. TROUBLESHOOTING...
User Manual - Page 17
... Pin Assignments
1000Mbps, 1000Base T Contact 1 2 3 4 5 6 7 8
MDI BI_DA+ BI_DABI_DB+ BI_DC+ BI_DCBI_DBBI_DD+ BI_DD- That means you can directly connect the Switch to another switch, a bridge or a hub, a straight or crossover cable is beyond the scope of the Switch supports auto-MDI/MDI-X detection. Implicit implementation of the crossover function within a twisted-pair cable, or at a wiring...
User Manual - Page 18
... standard cable, RJ-45 pin assignment
The standard RJ-45 receptacle/.connector
There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and color of straight cable and crossover cable connection: Contact
1 2 3 4, 5 6 7, 8
RJ-45 Connector pin assignment
MDI Media Dependant
Interface...
Netgear SW502 Reviews
We have not received any reviews for Netgear yet.