Netgear FSM7328PS - ProSafe 24 Port 10/100 L3 Managed Stackable Switch Support and Manuals
Get Help and Manuals for this Netgear item
This item is in your list!
View All Support Options Below
Free Netgear FSM7328PS manuals!
Problems with Netgear FSM7328PS?
Ask a Question
Free Netgear FSM7328PS manuals!
Problems with Netgear FSM7328PS?
Ask a Question
Popular Netgear FSM7328PS Manual Pages
FSM7328PS Command line reference manual - Page 25
...
This document is written for the 7300S Series Stackable Switch according to view and configure the 7300S Series Stackable Switch software. It also assumes that the reader has an understanding of the configuration options. Manual Specifications
Product Manual Part Number Manual Publication Date
ProSafe 7300S Series Layer-3 Managed Stackable Switch 202-10237-03 January 2008
About This...
FSM7328PS Command line reference manual - Page 38
... specified IP address. Select DHCP, BootP, or None as the network config protocol.
Display help logout ping show
Enter into user privilege mode. Exit this session. Configure the Management VLAN ID of... Any unsaved changes are lost. Configure Network Parameters of the router. Display switch options and settings. enable help for the ProSafe 7300S Series Layer-3 Stackable Switches,...
FSM7328PS Command line reference manual - Page 42
.... Command Line Interface Reference for the switch manually. If you use the dhcp parameter, the switch periodically sends requests to the default.
The IP Address and the gateway must configure the network information for the ProSafe 7300S Series Layer-3 Stackable Switches,
3.1.2 network parms (parameter)
This command sets the IP Address, subnet mask and gateway of the device...
FSM7328PS Command line reference manual - Page 70
...Default
enabled
Format
auto-negotiate
Mode
Interface Config
4-2
Port and System Setup Commands
v3.0, January 2008
Type a question mark (?) after entering the interface configuration mode to a set of ports.
Mode
Global Config
4.1.3 interface vlan
This command gives you access to to the vlan virtual interface mode, which allows certain port configurations (for the ProSafe...
FSM7328PS Command line reference manual - Page 83
... packet. Command Line Interface Reference for SNTP clients.
4.3.11 show sntp server
Mode
Privileged EXEC
Server IP Address
IP Address of configured SNTP Server
Server Type
Address Type of the server. The highest SNTP version the client supports SNTP Client Port Configured SNTP Client Mode Poll interval value for SNTP clients in seconds as a power of the server for...
FSM7328PS Command line reference manual - Page 92
... a defined protocol to IP addresses. DNS is determined by providing an IP address for the ProSafe 7300S Series Layer-3 Stackable Switches,
4.5 DNS Client Commands
The Domain Name System (DNS) is purged.
The following applications support domain name in the DNS cache. The DNS servers list is configured by the order in the switch.
A default domain name can be...
FSM7328PS Command line reference manual - Page 93
.... is IP addresses of this command. To remove a name server, use the ip domain-name global configuration command. Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches,
4.5.1 ip domain-lookup
To enable the IP Domain Naming System (DNS)-based host name-to-address translation, use the no ] ip domain-lookup
Mode
Global Config
Default
enabled
4.5.2 ip domain...
FSM7328PS Command line reference manual - Page 100
... specify 0 (defined as the default CIST ID) as the , the configurations are done for MST instance '0' i.e. CIST instance. Default
cost: auto; Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches,
5.1.11 spanning-tree max-hops
This command sets the MSTP Max Hops parameter to a new value for this port within the multiple spanning...
FSM7328PS Command line reference manual - Page 101
...on the parameter, to the default value, i.e. 128.
If the you specify port-priority, this command sets the priority for this port within a range of multiple instances supported by the switch is a ... If you are configuring the common and internal spanning tree instance. If you specify 0 (defined as the default CIST ID) as the , you are configuring that corresponds to be added...
FSM7328PS Command line reference manual - Page 278
... all VLAN routing interfaces. Logical Interface Shows the logical unit/slot/port associated with routing enabled.
Format
show ip vlan
This command displays the VLAN routing information for the ProSafe 7300S Series Layer-3 Stackable Switches,
14.4.2 show ip vlan
Modes
Privileged EXEC
User EXEC
MAC Address used by Routing VLANs
Is the MAC Address associated with this VLAN.
FSM7328PS Command line reference manual - Page 280
...255. The parameter is simple text password. Format
no authorization
Format
ip vrrp authentication {none | simple }
Mode
Interface Config
14-26
v3.0, January 2008
Routing Commands Default
none
Format
ip vrrp ip
Mode
Interface Config
14.5.5 ip vrrp authentication
This command sets the authorization details value for the virtual router configured on the specified interface. The...
FSM7328PS Command line reference manual - Page 285
... OSPF, which is not available on the specified virtual router. Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches,
14.5.12 show ip vrrp interface
Modes
Privileged EXEC User EXEC
IP Address
This field represents the configured IP Address for the Virtual router.
Administrative Mode
Represents the status (Enable or Disable) of the specified...
FSM7328PS Command line reference manual - Page 370
... that packets actually take when traveling to their factory defaults.
18.2.1 traceroute
Use the traceroute command to discover the routes that the reset should be an unused port on a hop-by-hop basis. When you automatically reset the switch.
Format
clear counters { | all the ports, or for the ProSafe 7300S Series Layer-3 Stackable Switches,
18.2 System Utility...
FSM7328PS Command line reference manual - Page 372
...For TFTP, the parameter is the IP address of the server, is the path...vlan
This command resets VLAN configuration parameters to a server. Format
copy
Mode
Global Config
Replace the and parameters with the options in Table 18-1. Copies the error log file to the factory defaults. Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches,
18.2.7 clear port...
FSM7328PS Command line reference manual - Page 387
...8226; TACACS Server (port 49) • Time Service (port 37)
The system supports a maximum of 128 interface address-port pairs. You can have an entry in the UDP port-to IP address mapping table is configured for 'All' interfaces are checked. Note that if the configured destination IP address is 0.0.0.0, then the packet is forwarded to the configured IP address. Otherwise the packet is...
Netgear FSM7328PS Reviews
Do you have an experience with the Netgear FSM7328PS that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Netgear yet.
Earn 750 points for your review!