Home » Netgear » Hubs & Switches » Netgear SW502

Netgear SW502 Support Question

Find answers below for this question about Netgear SW502 - Switch.
Need a Netgear SW502 manual? We have 1 online manual for this item!

Netgear Overview Questions Manuals Reviews Videos Research

Question posted by ChrisRobinson on September 7th, 2011

Can I Get A Datasheet For The Old Bay Network Switch, Part Number Sw502?

Also what Netgear part number whould you recommend, as a close replacement for the SW502? And will this new part be discontinued soon? (I will also need to know the UL Certification number.) Thank you for your help, Chris

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by kcmjr on September 7th, 2011 2:46 PM

This answer was accepted by the poster of the original question.

kcmjr

Member since:
May 5th, 2011

Points: 4,254,255

1,110
points

This the best I can do. No one has the manual available since this is so old.Manufactured by: NETGEAR

Model/Part : SW502
Product Type: Switch
Enclosure Type: Rack-mountable - external
Networking Ports Qty: 2 x Ethernet 10Base-T, Ethernet 100Base-TX
Data Transfer Rate: 100 Mbps
Data Link Protocol: Ethernet, Fast Ethernet
Connectivity Technology: Wired
Communication Mode: Half-duplex, full-duplex
Switching Protocol: Ethernet
Status Indicators: Link activity, collision status, port transmission speed, power, transmit, receive
Features: Full duplex capability, auto-sensing per device
Compliant Standards: IEEE 802.3, IEEE 802.3u
Interfaces: 1 x network - Ethernet 10Base-T/100Base-TX - RJ-45 female - 1, 1 x network - Ethernet 10Base-T - RJ-45 female - 1, 1 x network - Ethernet 10Base-T - BNC female - 1, 1 x network - Ethernet 10Base-T - 15 pin D-Sub (DB-15) female - 1
Power Device: Power supply - internal
Voltage Required: AC 110/220 V � 10% ( 50/60 Hz )
Power Consumption Operational: 22 Watt
Enclosure Color: Blue

This is a 10/100 unmanaged switch. Virtually any switch you buy today will be not just equivalent but better. For example: http://www.newegg.com/Store/SubCategory.aspx?SubCategory=30&name=Switches

Don't expect any particular device to be on shelves within 3 years of initial release.

You'll need to check the box toi find a UL cert number, not sure why you would even need that for these. These things are designed to be dirt cheap. Many may not even have UL listings.

Licenses & Certifications: Microsoft, Cisco, VMware, Novell, FCC RF & Amateur Radio licensed.

Related Netgear SW502 Manual Pages

User Manual - Page 3

... frequency energy and, if not installed and used in accordance with the limits for a Class A digital device, pursuant to radio communications. Revision PLANET Fast Ethernet Switch User's Manual FOR MODELS: GSD-503/GSD-504/GSD-803/GSD-804 Rev: 1.0(May.2005) Part No.: 2011-A33160-000 CE Mark Warning This is...

User Manual - Page 4

... carton including the original packing material, and use them against to repack the product in case there is a need to return it to us for repair. 1.2 How to Use This Manual This Fast Ethernet Switch User Manual is structured as follows: Chapter 2 Installation The chapter explains the feature, functionality and the physical...

User Manual - Page 5

... 10/100Mbps Auto-Negotiation ports - 10/20Mbps, 100/200Mbps Auto-sensing fCompact size design for wall mount or desktop placement fHigh performance Store-and-Forward Switching Architecture fRunt and CRC filtering fFlow control (Back Pressure) supports in half-duplex mode f1K MAC Address Table, automatically learning and aging fLED indicators array...

User Manual - Page 6

1.4 Product Specifications Model SW-502 SW-802 Hardware Specification Network Ports 5 10/100Base-T RJ-45 8 10/100Base-T RJ-45 MDI/MDI-X ports MDI/MDI-X ports Dimensions (W x D x H) 159 x 100 x 28mm Weight (KG) 0.16 KG 0.18 KG Power Requirement External Power adapter 12V 500 mA Switch Specification Switch Architecture Store-and-forward Address Table 1K entries...

User Manual - Page 7

... can also automatically identify and determine the correct transmission speed and half/full duplex mode of networking is a Simple and cost-effective, highly reliable network switch. Basic knowledge of the attached devices with its 5/8 ports. Please read this chapter completely before continuing. 2.1 Product Description With concepts of 10 to Install and ...

User Manual - Page 8

... latency and high data integrity, eliminates unnecessary traffic and relieves congestion on critical network paths. This product also supports store-and-forward forwarding scheme to 1K different MAC address and enables filtering and forwarding at full wire speed. 2.1.2 Switch Front Panel Figure 2-1 & 2-2 show the front panel and rear panel of SW-502...

User Manual - Page 9

Power Notice: 1. If your networks should active all the time, please Blink: indicate that the switch is actively sending or receiving data over that the Switch is powered on. The device is a power-required device, it means, it will not work till it is successfully established. Figure 2-3 SW-802 front panel 8 7 6 5 4 3 2 1 ...

User Manual - Page 10

... in Chapter 1, Section 1.4 Product Specification. In some area, installing a surge suppression device may also help to protect your switch from network data loss or network downtime. 2. Connect one end of the switch. Step4: Connect your Fast Ethernet Switch and make connections to network devices. consider using UPS (Uninterrupted Power Supply) for your device. It will prevent you...

User Manual - Page 11

Step5: Supply power to the switch requires UTP Category 5 network cabling with RJ-45 tips. Note: Connection to the switch. A. Connect one end of the power cable to the switch. B. When the switch receives power, the Power LED should remain solid Green. Connect the power plug of the power cable to a standard wall outlet. For more...

User Manual - Page 12

... be forwarded to decide either forwarding or filtering for the destination address. Thereby increase the network throughput and availability. 3. The Ethernet Switching will transmit this destination address is used to all the other related information in , the Ethernet Switching will also check the destination address besides the source address learning. This address table...

User Manual - Page 13

... one type of each incoming and outgoing packet are stored in any Ethernet network environment to significantly boost bandwidth using conventional cabling and adapters. Due to the learning function of the Ethernet switching, the source address and corresponding port number of packet-forwarding techniques. This technology automatically sets the best possible bandwidth when...

User Manual - Page 14

connection is established with the port in Full-duplex mode. This is connected and capable of both device is done by detect the modes and speeds at Power On or Reset). or Full-Duplex mode. 1000Base-T can connect with another network device (usually at the second of , both 10Base-T and 100Base-TX devices can be only connected in either Half-

User Manual - Page 15

...help you solve problems. If Giga Switch is set up according to half duplex, then the performance will be poor. If the Ethernet Switch is set to full duplex and the partner is not functioning properly, make sure the Ethernet Switch...contain older information than of the address table of the Ethernet Switch. After a while, turn on the Switch I Make sure the cable is installed properly Make sure ...

User Manual - Page 17

... A.2 10/100Mbps, 10/100Base-TX When connecting your 10/100Mbps Ethernet Switch to any Ethernet devices without making a crossover cable. The following table and...you can directly connect the Switch to another switch, a bridge or a hub, a straight or crossover cable is beyond the scope of the Switch supports auto-MDI/MDI-X detection. Appendix A A.1 Switch's RJ-45 Pin Assignments ...