User Guide
Page 58
...address • IP subnet mask • Default gateway IP address NOTE: The Setup Wizard assumes the following information from the network administrator: • SNMP Community String and SNMP Management System IP address (optional) • Username and password 58 Dell PowerConnect 55xx Systems User Guide See "Assigning Unit...quickly as when you through the CLI. To configure the system using the Setup Wizard: 1 Obtain the following : • The PowerConnect switch was never configured before and is in the stack, each switch must be a stack of the switch (see Figure 5-2). ...
...address • IP subnet mask • Default gateway IP address NOTE: The Setup Wizard assumes the following information from the network administrator: • SNMP Community String and SNMP Management System IP address (optional) • Username and password 58 Dell PowerConnect 55xx Systems User Guide See "Assigning Unit...quickly as when you through the CLI. To configure the system using the Setup Wizard: 1 Obtain the following : • The PowerConnect switch was never configured before and is in the stack, each switch must be a stack of the switch (see Figure 5-2). ...
User Guide
Page 73
... commands: console(config)# ip http authentication aaa loginauthentication local console(config)# username admin password user1 privilege 15 Enter the following commands once when configuring use of a terminal, a Telnet, or an SSH session, for the page content to the configuration level access. Dell PowerConnect 55xx Systems User Guide 73 console(config)# crypto certificate 1 generate keygenerate...
... commands: console(config)# ip http authentication aaa loginauthentication local console(config)# username admin password user1 privilege 15 Enter the following commands once when configuring use of a terminal, a Telnet, or an SSH session, for the page content to the configuration level access. Dell PowerConnect 55xx Systems User Guide 73 console(config)# crypto certificate 1 generate keygenerate...
User Guide
Page 129
... port as an untagged member of the devices as the username and password, when communicating with RADIUS attributes tunnel-type (64) = VLAN (13), tunnel-media-type (65) = 802 (6), and tunnel-privategroup-id = a VLAN ID. The switch supports this guide. MAC addresses for Dell PowerConnect 55xx Systems User Guide 129 The switch emulates the supplicant...
... port as an untagged member of the devices as the username and password, when communicating with RADIUS attributes tunnel-type (64) = VLAN (13), tunnel-media-type (65) = 802 (6), and tunnel-privategroup-id = a VLAN ID. The switch supports this guide. MAC addresses for Dell PowerConnect 55xx Systems User Guide 129 The switch emulates the supplicant...
User Guide
Page 130
..." on page 459. An unauthenticated VLAN is configured with no delimiting characters (for example: aaccbb55ccff). username and password must be defined. - The Dot1x supplicant preempts an authorized, but non-Dot1x device, at a ...following characteristics: • It must be a static VLAN, and cannot be the Guest VLAN or the default VLAN. • The VLAN's member ports must be manually configured as tagged members. • The ...connected and Guest VLAN enabled. 130 Dell PowerConnect 55xx Systems User Guide An access port cannot be Dot1x or MAC-Based authenticated and authorized....
..." on page 459. An unauthenticated VLAN is configured with no delimiting characters (for example: aaccbb55ccff). username and password must be defined. - The Dot1x supplicant preempts an authorized, but non-Dot1x device, at a ...following characteristics: • It must be a static VLAN, and cannot be the Guest VLAN or the default VLAN. • The VLAN's member ports must be manually configured as tagged members. • The ...connected and Guest VLAN enabled. 130 Dell PowerConnect 55xx Systems User Guide An access port cannot be Dot1x or MAC-Based authenticated and authorized....
Getting Started Guide
Page 16
To configure the system using the Setup Wizard: 1 Obtain the following : • The PowerConnect switch was never configured before and is in the stack, each switch must be a stack of a VT100 terminal switch. See "Unit ID ...Setup Wizard configures the following fields: • SNMP Community String and SNMP Management System IP address (optional) • Username and password • Management switch IP address • IP subnet mask • Default gateway IP address NOTE: The Setup Wizard assumes the following information from the network administrator: • SNMP Community String...
To configure the system using the Setup Wizard: 1 Obtain the following : • The PowerConnect switch was never configured before and is in the stack, each switch must be a stack of a VT100 terminal switch. See "Unit ID ...Setup Wizard configures the following fields: • SNMP Community String and SNMP Management System IP address (optional) • Username and password • Management switch IP address • IP subnet mask • Default gateway IP address NOTE: The Setup Wizard assumes the following information from the network administrator: • SNMP Community String...