Dell PowerConnect 7048 Support and Manuals
Get Help and Manuals for this Dell item
View All Support Options Below
Free Dell PowerConnect 7048 manuals!
Problems with Dell PowerConnect 7048?
Ask a Question
Free Dell PowerConnect 7048 manuals!
Problems with Dell PowerConnect 7048?
Ask a Question
Dell PowerConnect 7048 Videos
Dell PowerConnect 7048 $3095 Price Reduction
Duration: :34
Total Views: 35
Duration: :34
Total Views: 35
Popular Dell PowerConnect 7048 Manual Pages
- Page 50
... the PowerConnect 7000 Series switches are available at support.dell.com/manuals:
• Getting Started Guide-provides information about the command-line interface (CLI) commands used to configure and ... describes the installation and initial configuration procedures.
• CLI Reference Guide-provides information about the switch models in -depth CLI descriptions, syntax, default values, and...
- Page 128
... mode for VLAN 1.
128
Setting Basic Network Information
ip address dhcp
Enable the DHCP client. CTRL + Z
Exit to Privileged EXEC mode.
Configuring Basic Network Information (CLI)
This section provides information about these commands, see the PowerConnect 7000 Series CLI Reference Guide.
band
Enabling the DHCP Client on the Default VLAN
Beginning in Privileged EXEC...
- Page 155
... and view information about the switch stack. The running configuration is 1-10.
NOTE: Changing the ID number causes all switches in Privileged EXEC mode.
Managing the Stack (CLI)
This section provides information about the commands you use to perform Management unit renumbering.
For more information about these commands, see the PowerConnect 7000 Series CLI Reference Guide.
- Page 335
... or colon. (Range: 6-32 characters)
• default - Configuring the SNMPv3 Engine ID
To use the default keyword to manage and view SNMP features on both the password and the local engine ID. The engineID is converted to be separated by RFC 2274. Configuring SNMP (CLI)
This section provides information about these commands, see the PowerConnect 7000 Series CLI Reference Guide.
- Page 387
... the PowerConnect 7000 Series CLI Reference Guide. boot host autoreboot Allow the switch to Privileged Exec mode. show boot
Displays the current status of attempts to the switch by sending unicast TFTP requests, and if unsuccessful, broadcast TFTP requests) specified in Privileged EXEC mode, use the following commands to manually activate the Auto Configuration process and...
- Page 440
...one bound to a specific IP address, the address...ip-address-IP address of a new session or connection. iscsi cos {enable | disable | Set the quality of service profile that will be defined in the system in the first login request of the iSCSI target. Configuring iSCSI Optimization (CLI)
This section provides information about the commands, see the PowerConnect 7000 Series CLI Reference Guide...
- Page 899
...
This section provides information about the commands, see the PowerConnect 7000 Series CLI Reference Guide. Configuring Global IP Routing Settings Beginning in Privileged EXEC mode, use to configure IPv4 routing on the switch.
Configure the global default gateway for the switch. The gateway configured here takes precedence over a default gateway assigned by a network DHCP server. View the...
- Page 981
... mode.
The metric (or preference) value of default routes. Configuring OSPF and OSPFv3
981 Configuring OSPFv3 Features (CLI)
This section provides information about additional show commands, see the PowerConnect 7000 Series CLI Reference Guide.
Normally, OSPFv3 originates a default route
[metric metric-value]
only if a default route is redistributed into OSPFv3 (and
[metric-type...
- Page 1014
... auto-summarization mode. originate
default-metric metric- Configuring RIP Features (CLI)
This section provides information about the commands, see the PowerConnect 7000 Series CLI Reference Guide.
split-horizon {none | Set the RIP split horizon mode.
NOTE: RIP is the metric (or preference) value
of the default route. (Range: 1-15)
enable
Reset the default administrative mode of RIP in...
- Page 1125
... PowerConnect 7000 Series CLI Reference Guide. For more information about the commands you use to configure the CoS mapping tables. Mapping Table Configuration Beginning in Privileged Exec mode, use this command in to configure CoS settings on all interfaces. You can also use the following commands in Global Configuration mode to internal traffic classes for a specific interface.
CLI...
- Page 1135
... of the switch.
Exit to Privilege Exec mode.
Configuring Auto VoIP
1135
Mapping Table Configuration Beginning in to enable Auto VoIP and view its configuration.
Configuring Auto VoIP (CLI)
This section provides information about the commands, see the PowerConnect 7000 Series CLI Reference Guide. Exit to Global Configuration Exec mode. For more information about the commands...
Getting Started Guide - Page 25
..., see the CLI Reference Guide.
Before setting up the initial configuration of the management interface default gateway. If POST passes successfully, valid firmware is completed.
The boot process runs for the network.
• The IP address of the switch, obtain the following assumptions:
• The PowerConnect switch was established, and the Dell Easy Setup Wizard prompt...
Getting Started Guide - Page 26
... used for the VLAN 1 routing interface, of -band (OOB) management.
Additionally, you can use the default values. The wizard sets up the SNMP community string to the right of VLAN 1. See the CLI Reference Guide for in -band ports are members.
• Sets up the following configuration on the front panel for information about performing the initial...
Getting Started Guide - Page 32
... watts
180 watts
720 watts
180 watts
1440 watts
30
Getting Started Guide Use the Web-based management interface or the CLI to comply with regulatory testing requirements. For information about how to configure the switch features, see the User's Configuration Guide or CLI Reference Guide included on the User Documentation CD or available on the support site: support.dell.com/manuals.
Getting Started Guide - Page 233
...-band
• VLAN 1 show ip interface
Dell OpenManage Switch Administrator Web OOB または VLAN 1 IP CLI Telnet または SSH OOB または VLAN 1 IP CLI
PowerConnect 7000 VLAN 3 CLI User Documentation CD Users Configuration Guide CLI Reference Guide』（CLI support.dell.com/manuals
はじめに...
Dell PowerConnect 7048 Reviews
We have not received any reviews for Dell yet.