Cisco 1601 - Router - EN Support and Manuals
Get Help and Manuals for this Cisco item
Most Recent Cisco 1601 Questions
What Driver Do I Need To Program A 1601-r Cisco Router?
(Posted by pkillian 12 years ago)
Popular Cisco 1601 Manual Pages
Hardware Installation Guide - Page 25
...
2-port T1/E1 radio access VWIC-2T1/E1-RAN network optimization VWIC
Voice Interface Cards
2-port Direct Inward Dial VIC-2DID (DID) VIC
1-port digital VIC for Japan
VIC-1J1
Supported on Cisco Routers Cisco 17215 Cisco 1751 Cisco 1760 Cisco 1800 series (modular) Cisco 2600 series Cisco 2800 series Cisco 3600 series Cisco 3700 series Cisco 3800 series Cisco 17215 Cisco 1751 Cisco 1760 Cisco 1800...
Hardware Installation Guide - Page 31
... access the documents located at Products and Solutions > Cisco IOS Software > Cisco IOS release you are using > Cisco IOS Software Releases > Technical Documentation > Feature Guides.
To find configuration examples specific to compare two different Cisco IOS releases, access Cisco Feature Navigator II, located at Products and Solutions > Routers > Router series you are using > Cisco IOS...
Hardware Installation Guide - Page 53
... the Cisco IOS show running-config or show diag commands. For more processing power. Timesaver To configure digital voice ports correctly, any additional PVDMs must be recognized as a voice port. Warning After wiring the DC power supply, remove the tape from the circuit breaker switch handle and reinstate power by moving the handle of voice ports on locating additional hardware documentation...
Hardware Installation Guide - Page 57
...Cards in Cisco Access Routers
Installing Other Accessories in Cisco Interface Cards
Installing Other Accessories in the SFP port. for proper seating of the port when no fiber cable is connected, avoid exposure to secure the module in Cisco Interface Cards
Certain Cisco interface cards support a variety of the SFP. Installing and Removing SFPs
SFPs are hot-swappable Ethernet interfaces that...
Hardware Installation Guide - Page 70
... or DCE format. For example, the network end of the EIA/TIA-232 serial cable is properly grounded. Refer to the Cisco Modular Access Router Cable Specifications for your HWIC, refer to digital WAN lines
The 4-port serial HWICs have 68-pin serial ports. OL-12843-01
10
and 16-port serial HWICs have 26-pin 12-in Cisco Access Routers. Use the correct cable for network end connectors...
Hardware Installation Guide - Page 77
... equipment is properly grounded. Newer WIC-1B-S/T or WIC-1B-U interface cards can mount in Cisco Access Routers.
ISDN port has established a connection with is properly grounded, and you have termination jumpers. Installing a Cisco ISDN BRI S/T WAN Interface Card
Install the Cisco WIC according to the network.
Table 9
LED B1 B2 OK
ISDN BRI S/T WIC LEDs
Description ISDN...
Hardware Installation Guide - Page 81
... have termination jumpers. Setting Jumpers on grounding your installation. Installing a Cisco ISDN BRI S/T WAN Interface Card
Install the Cisco WIC according to Installing Cisco Interface Cards in Cisco Access Routers.
Table 10
LED B1 B2 OK
ISDN BRI U WIC LEDs
Description ISDN connection on BRI network modules, see the Cisco Network Modules Hardware Installation Guide.
Newer WIC-1B...
Hardware Installation Guide - Page 84
...Installing a Cisco ISDN BRI S/T WAN Interface Card
Install the Cisco WIC according to Installing Cisco Interface Cards in Cisco Access Routers.
This section describes the preparation necessary before connecting an ISDN BRI U WIC to the network, ensure that the equipment you have the proper cables... Front Panel ISDN BRI port
41216
BRI S/T LL SEE MANUAL BEFORE INSTALLATION
B1 LED B2 LED OK...
Hardware Installation Guide - Page 95
... follow these steps: Step 1 Confirm that appear.
Figure 61
Connecting the T1/FT1 DSU/CSU WIC to a T1 Wall Jack
T1 port (RJ-48C)
SEE MANUAL BEFORE
INSTALLATION
LP AL CD
LOOP BACK T1 DSU/CSU
DSU CSU
T1
Straight-through RJ-48C-to-RJ-48C cable to the router. Finding Support Information for Cisco Interface Cards.
Hardware Installation Guide - Page 112
...scenarios for using splitters and microfilters. This type of building
39196
Optional microfilters
Cisco router
Customer-Installed Splitter
This scenario is described below and illustrated in Figure 77. •...both the telephone
(POTS) service and the router with an ADSL-over-POTS WIC (WIC-1ADSL)
DSL Interface Cards
Common Splitter and Microfilter Configurations
This section describes the ...
Hardware Installation Guide - Page 114
..., see the "Obtaining Documentation, Obtaining Support, and Security Guidelines" section on Cisco 1700, Cisco 2600, and Cisco 3600 Series Routers, Cisco IOS Releases 12.2(4)XL and 12.2(13)T
Sample Configurations - Feature Modules - Voice and Quality of Service Features for ADSL and G.SHDSL on a Cisco 2600/3600 With ADSL-WIC and Hardware Encryption Modules - Configuring a Cisco 1700/2600/3600...
Hardware Installation Guide - Page 154
...a stacking port, and as such, does not support inline power.
See the "Stacking of the Cisco 10/100BASE-T Ethernet switch HWIC is provided by a -48 volt power supply within the router. The ninth port (port 8) is used to provide power to an IP phone or to a wireless access point attached to the ports of its ports.
The daughter card distributes the -48 volt power to a port. Figure...
Hardware Installation Guide - Page 178
...) • High-Speed Downlink Packet Access (HSDPA) It supports multiple bands on the multiple services for use in different parts of a 3G wireless WAN HWIC.
...services HWIC-3G-GSM is the Cisco part number for which the interface card is configured. Figure 121 1
HWIC-3G-GSM Front Panel
2
3
1
ANT
170842
HWIC3G-GSM WWAN RSSI
44
Diag Port
UMTS HSDPA
44
1 Mounting Screws 2 Diagnostic Port...
Hardware Installation Guide - Page 193
...• Related Documentation, page 9 • Obtaining Documentation, Obtaining Support, and Security Guidelines, page 10 For an overview of Cisco interface cards used for Cisco access routers see the Cisco Interface Cards for Cisco Access Routers document. HWIC-AP-G-E-Europe - There are configured: - HWIC-AP-G-A-North America - HWIC-AP-G-J-Japan
OL-12854-01
1 Access Point High-Speed WAN...
Hardware Installation Guide - Page 195
..., the national codes, and the safety directors of such environments. Access Point HWIC Safety Guidelines and Warnings
The following : • Only one access point HWIC is supported in the router at the circuit breaker on DC units.
Installation of Conformity and Regulatory Information for Cisco Access Products with 802.11a/b/g and 802.11b/g Radios document. Access Point High-Speed...
Cisco 1601 Reviews
We have not received any reviews for Cisco yet.