Cisco 2501 - Router - EN Support and Manuals
Get Help and Manuals for this Cisco item
Cisco 2501 Videos
Cisco 2501 Router Bootup problem
Duration: :52
Total Views: 81
Duration: :52
Total Views: 81
Popular Cisco 2501 Manual Pages
Getting Started Guide - Page 25
...CPU01: Core 1 Initialization: ok Fastpath CPU00: Initializing Timer...done. Installing ether-pow driver - 0x6008 starting pid 805, tty '/dev/ttyS0': '/usr/bin/gettyOrMwar' Cryptographic library self-test....passed! Software Copyright Cisco Systems, Inc. Num of Cisco Systems, Inc. Starting Switching Services: ok Starting QoS Services: ok Starting Policy Manager: ok Starting Data Transport Link...
Getting Started Guide - Page 27
...) 3. Format FLASH Drive 6. XML config selected Validating XML configuration octeon_device_init: found 1 DPs /dev/fpga: No such device or address readCPUConfigData: cardid 0x6060001 Cisco is a trademark of Cisco Systems, Inc. Run primary image (7.0.114.76) - Loading primary image (7.0.114.76) 100% 31427987 bytes read Launching images... Clear configuration 5. Manually update images...
Getting Started Guide - Page 30
... or 0 for each . Ports values are 1 to the controller.
You can enter up to match the switch interface configuration.
You can access the controller GUI interface using the management interface IP address. Enter the IP address of the controller and connectivity to 4]
Note There is no default administrative password, you must enter a password. Note Press the hyphen...
User Guide - Page 1
...
This section discusses the objectives, audience, organization, and conventions of interfaces supported.
Troubleshooting, maintenance procedures, and cable specifications are similar in functionality, but differ in the "Overview of router models that came with electronic circuitry and wiring practices and have experience as comprehensive router configuration instructions.
User Guide - Page 25
...
EIA/TIA-232
EIA/TIA-449
V.35
X.21
Network connections at the modem or CSU/DSU
EIA-530
Although attempting to manufacture your own serial cables is not recommended (because of the small size of the Router" chapter.
Preparing to the section "Obtaining Service and Support" in the "Overview of the pins on the...
User Guide - Page 27
... to the section "Obtaining Service and Support" in Figure 2-4. V.35 cables are available with a standard V.35 plug or receptacle in Figure 2-3. The end that connects to Install the Router 2-13 The network end ... Router" chapter.
Preparing to the serial port on the rear panel of the router has a DB-60 connector. The end that connects to the serial port on the rear panel of the router ...
User Guide - Page 30
...is 1,640 feet (500 meters) for use with console terminals.
2-16 Router Installation and Configuration Guide Because the auxiliary port supports flow control, it before connecting a console terminal (an ASCII terminal or PC running terminal emulation software) to the console port or modem to the auxiliary port. therefore, the console port is that the receiving device can operate at...
User Guide - Page 50
... console port on the router:
Step 1
Connect the terminal using the thin, flat, RJ-45-to-RJ-45 roll-over cable (looks like a telephone cable) and an RJ-45-to-DB-9 or RJ-45-to your terminal or PC terminal emulation software for 9600 baud, 8 data bits, no parity, and 2 stop bits.
3-18 Router Installation and Configuration Guide...
User Guide - Page 55
...64257;guring the Router for ordering information. Configuring the Router 4-1 CHAPTER 4
Configuring the Router
This chapter describes how to the section "Ordering Documentation" in the Cisco IOS configuration guide and command reference publications.
Detailed software configuration information is not meant as comprehensive router configuration instructions. it is...
User Guide - Page 66
Refer to the Cisco IOS configuration guide and command reference publications for the router using the hostname command. (b) Enter an enable secret password using the enable password command. (c) Assign addresses to the interfaces using the protocol address command. (d) Specify which protocols to support on the interfaces. Configuring the Router for the First Time
Using Confi...
User Guide - Page 67
... to the Cisco IOS configuration guide and command reference publications. Router# copy running -config startup-config command at the site where the TCP/IP host is located. For more information, refer to use AutoInstall unless the required files have been provided on the remote side of the WAN connection is connected and...
User Guide - Page 71
...commands. Do not include a space. configure connect copy
To list keywords or arguments, enter a question mark in those ...running configuration is a system reload or power outage. Router# configure ? Configuring the Router 4-17 Include a space before the question mark. The running (current operating) configuration and the startup configuration. Cisco IOS Software...
User Guide - Page 74
... 5ESS service configured for the channel. The value ranges from 1 to work, the router must be running Cisco IOS Release 11.0(3) or a later release, and both the current router and target router must support Multilink PPP:
Router (config-if)# ppp multilink
4-20 Router Installation and Configuration Guide
For bandwidth on demand, enter the load-threshold command to set up a second...
Configuration Guide - Page 2
... • Configuration Builder Getting Started Guide • Router Products Getting Started Guide • Router Products Configuration Guide • Router Products Command Reference • Troubleshooting Internetworking Systems
These publications are available on CIO to obtain additional content and services.
4-2 Cisco 2500 Series Access Server User Guide All Cisco technical documentation...
Configuration Guide - Page 9
... Flash memory, the following the instructions in the section "Connecting the Console Terminal and Modem" in Technical Data and Computer Software clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in the chapter "Installing the Cisco 2500 Series Access Server" and then boot the access server to the EXEC prompt (Router>).
Note You can run the setup...
Cisco 2501 Reviews
We have not received any reviews for Cisco yet.