Cisco 1605 - Router - EN Support and Manuals
Get Help and Manuals for this Cisco item
Cisco 1605 Videos
Steve Parker & Cisco Arias - Underneath (Original Mix) [1605-042]
Duration: 7:08
Total Views: 6,257
Duration: 7:08
Total Views: 6,257
Popular Cisco 1605 Manual Pages
Hardware Installation Guide - Page 25
...
Supported on Cisco Routers Cisco 17215 Cisco 1751 Cisco 1760 Cisco 1800 series (modular) Cisco 2600 series Cisco 2800 series Cisco 3600 series Cisco 3700 series Cisco 3800 series Cisco 17215 Cisco 1751 Cisco 1760 Cisco 1800 series (modular) Cisco 2600 series Cisco 2800 series Cisco 3600 series Cisco 3700 series Cisco 3800 series Cisco 17215 Cisco 1751 Cisco 1760 Cisco 1800 series (modular) Cisco...
Hardware Installation Guide - Page 31
...8226; Software references-Command references, system message guides • Software release information-Supported products, caveats • Software release tools-Cisco Feature Navigator II, Cisco IOS Upgrade Planner, software
downloads, security notices and advisories
Cisco IOS Software Configuration Documents
To find initial configuration instructions specific to the Cisco router you are using...
Hardware Installation Guide - Page 53
... (DSPs). Warning After wiring the DC power supply, remove the tape from the circuit breaker switch handle and reinstate power by moving the handle of voice ports on the Cisco ICS 7750, use the Cisco IOS show running-config or show diag commands. Preparing to Install Interface Cards on the Cisco ICS 7750
Before installing an interface card into the MRP...
Hardware Installation Guide - Page 54
... cards can cause erroneous system error messages indicating a card failure. Caution To prevent ESD damage, handle the cards only by unplugging the power supply.
To remove a card, hold the card by unplugging the power supply. Step 4
Step 5 Step 6
Disconnect any cables attached to lose important configuration data and interrupts any other part of the cards. Failure to...
Hardware Installation Guide - Page 57
...section on the side of the port when no fiber cable is designed to SFP model or technology type;
Installing Cisco Interface Cards in Cisco Access Routers
Installing Other Accessories in Cisco Interface Cards
Installing Other Accessories in Cisco Interface Cards
Certain Cisco interface cards support a variety of the SFP in the closed position for information on the SFP technology type...
Hardware Installation Guide - Page 70
... to the Cisco Modular Access Router Cable Specifications for the interface. All other DCEs, if connecting to the instructions in Installing Cisco Interface Cards in Cisco Access Routers. For instructions on grounding ... modems, if connecting to analog telephone lines
• Synchronous modems, data service units/channel service units (DSUs/CSUs), or other cables are working with is a DB...
Hardware Installation Guide - Page 77
... to a Network
Before connecting a WIC to -multipoint configuration, use an external 100-ohm terminator. Table 9
LED B1 B2 OK
ISDN BRI S/T WIC LEDs
Description ISDN connection on BRI network modules, see the Cisco Network Modules Hardware Installation Guide.
Grounding
Ensure that the WIC is installed in the router, the equipment is properly grounded. ISDN BRI WAN...
Hardware Installation Guide - Page 81
...interface cards mount only in Cisco Access Routers. For more information on ...instructions on grounding your installation. ISDN BRI WAN Interface Cards
ISDN BRI U WAN Interface Cards
ISDN BRI U WIC LEDs
The ISDN BRI U WIC LEDs are set appropriately for connecting the WIC to the network.
Setting Jumpers on BRI network modules, see the Cisco Network Modules Hardware Installation Guide...
Hardware Installation Guide - Page 84
... MANUAL BEFORE INSTALLATION
B1 LED B2 LED OK LED
ISDN BRI S/T Leased-Line WIC LEDs
The ISDN BRI S/T leased-line WIC LEDs are described in Table 11. For instructions on B2 channel (not used). This section describes the preparation necessary before connecting an ISDN BRI U WIC to the instructions in Installing Cisco Interface Cards in Cisco Access Routers...
Hardware Installation Guide - Page 95
... the RJ-48C port on power to the T1 wall jack, as shown in Figure 61.
The intrabuilding cable must be shielded and the shield must have forgotten your username or password, click Cancel at http://www.cisco.com/go/fn. Finding Support Information for Platforms and Cisco IOS Software Images Use Cisco Feature Navigator to -RJ...
Hardware Installation Guide - Page 112
...has provisioned a single copper pair to be used by both the telephone
(POTS) service and the router with a DSL interface card, so a POTS splitter must be
installed only if they improve telephone call quality. • For telephones connected directly to...WIC (WIC-1ADSL)
DSL Interface Cards
Common Splitter and Microfilter Configurations
This section describes the most common to least common.
Hardware Installation Guide - Page 154
... Layer 2 switching for traffic between different VLANs on the switch is intended to a port. Two Cisco 10/100BASE-T Ethernet switch HWICs can be inserted into WIC/VIC slots.
Inline power is provided by a -48 volt power supply within the router. The HWIC also supports Layer 3 traffic to and from the HWIC and any other platform interfaces...
Hardware Installation Guide - Page 158
...-MDIX only when configured in the following steps:
Step 1 Confirm that support inline power.
Connecting Cisco 10/100BASE-T Ethernet Switch HWICs to Your Network
To connect the Cisco 10/100BASE-T Ethernet switch HWIC to the network, perform the following scenarios: • Multiproduct WAN gateway routers for LANs • Same-building or same-campus wiring closets to...
Hardware Installation Guide - Page 178
.../900/1800/1900 MHz for GPRS and EDGE services • 850/1900/2100 MHz for UMTS and HSDPA services HWIC-3G-GSM is the Cisco part number for which the interface card is configured.
HWIC-3G-GSM
The GSM version supports the following sevices: • General Packet Radio Services (GPRS) • Enhanced Data Rates for GSM Evolution...
Hardware Installation Guide - Page 195
... on a chassis or working near power supplies, unplug the power cord on page 8. • The 4.9-GHz band is not supported. • Although the use of wireless devices in the router is not supported. • The access point HWIC must be used to the constraints posed by the local
codes, the national codes, and the safety directors of such...
Cisco 1605 Reviews
We have not received any reviews for Cisco yet.