GE ATP 1000 Support Question
GE ATP 1000 Support Question
Find answers below for this question about GE ATP 1000 - Security Concord Alphanumeric Touchpad.Need a GE ATP 1000 manual? We have 1 online manual for this item!
Question posted by melodale on November 16th, 2012
How To Set Time And Date On Ge Atp-1000 Keypad
The person who posted this question about this GE product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related GE ATP 1000 Manual Pages
Installation Instructions - Page 1
...;F to 120°F/0°C to indicate the current status of compatible security systems (see the "Specifications" section). The door can also be removed by the touchpad. • Table 2 describes the maximum wire lengths allowed between the touchpad and the panel. Touchpad Wire Length Between Touchpad and Panel
750 feet 300 feet
1 imum available power. •...
Installation Instructions - Page 2
...Mounting Hole Locations
3.
Remove panel AC and backup battery power. 2.
Touchpad Wiring Connections
Attaching the Touchpad to the touchpad location (see Figure 1). Gently tighten the screw into the wall at ...with the wall or gang box screw holes and secure the
back plate using the screws provided. 5. Loosen screw,
then lift touchpad.
Figure 2.
Align the mounting plate holes with...
Installation Instructions - Page 3
... bus device.
1.
Activate the touchpad by pressing 8 + installer/dealer code (default = 4321) + 0 + 0. Alphanumeric touchpads briefly show the date and time display. The display
should read BUS...and the display shows SECURITY. 5.
Verify that don't include an alphanumeric touchpad as a programming touchpad, be careful not to a Concord Express, Concord, or Concord Ultra panel with the...
Installation Instructions - Page 4
... Instructions Connect the cable plug onto the panel Programming Touchpad Header pins (see Figure 5). 3. Reconnect the AC and backup battery power.
The brightness adjustment lightens or darkens the background.
The display shows SYSTEM MENU, then TIME AND DATE (Concord panels with software versions 1.0-1.6:
1. Enter a setting from the panel header.
The display shows the lowest...
Installation Instructions - Page 5
... system may be set to the desired unit number before applying power and entering program mode.
• Whenever possible, assign touchpad unit numbers before all other panel programming. Press , to do if the touchpad does not operate correctly.
To change the touchpad unit number (see procedure on this time, the touchpad is plugged in Concord RF systems...
Installation Instructions - Page 6
... shows SCANNING BUS DEVICES, then a time and date display. See the specific panel Installation ...Concord is the only installed touchpad, remove panel AC and battery power, then re-apply power.
All other bus devices should operate correctly and any bus device. Note If the panel still indicates a bus failure the panel may cause harmful interference to correct the interference by GE...
Similar Questions
My Ge Atp 1000 Keypad Gets Blazing Hot. It Is Newly Installed Over Heating Duct.
Is it defective or does it need to be moved? Why would this happen?
Is it defective or does it need to be moved? Why would this happen?
(Posted by Axelrod6 11 years ago)
How Do You Set The Date And Time
I need to reset the date and time on the touch pad how do you doi this?
I need to reset the date and time on the touch pad how do you doi this?
(Posted by robertcouglar 11 years ago)
How Do I Set The Date And Time On The Simon Xt?
When we replaced the battery, the date and time just flash on the code box. We can't find the manual...
When we replaced the battery, the date and time just flash on the code box. We can't find the manual...
(Posted by jessiecaquay 12 years ago)
I Have A Ge Atp 1000 Keypad. Can The Keypad Beeps Get Shut Off Or Lowered.
Also, is it possible to turning the beeping off when arming the system? Thanks, John
Also, is it possible to turning the beeping off when arming the system? Thanks, John
(Posted by jcangi01 12 years ago)
How Do You Change The Time/date?
I need to change the time/date but the stupid instruction that came with the pad does not address th...
I need to change the time/date but the stupid instruction that came with the pad does not address th...
(Posted by res1wymz 13 years ago)