GE ATP 1000 Support Question
GE ATP 1000 Support Question
Find answers below for this question about GE ATP 1000 - Security Concord Alphanumeric Touchpad.Need a GE ATP 1000 manual? We have 1 online manual for this item!
Question posted by jcangi01 on December 13th, 2011
I Have A Ge Atp 1000 Keypad. Can The Keypad Beeps Get Shut Off Or Lowered.
Also, is it possible to turning the beeping off when arming the system?
Thanks,
John
Current Answers
Related GE ATP 1000 Manual Pages
Installation Instructions - Page 1
... area (32°F to 120°F/0°C to indicate the current status of compatible security systems (see the "Specifications" section).
The door can be removed by the touchpad. • Table 2 describes the maximum wire lengths allowed between the touchpad and the panel. The door can be reattached later if desired. A swingdown door reveals...
Installation Instructions - Page 2
... (see Figure 1). Gently tighten the screw into the wall at the top of the touchpad.
2
ATP1000 Touchpad/Display Installation Instructions
Insert anchors into the bottom of the mounting plate with the wall or gang box screw holes and secure the
back plate using the screws provided. 5. Align the mounting plate holes with the...
Installation Instructions - Page 3
... System Programming Only
After making all wiring connections from the touchpad to the panel, you must first connect a Programming Touchpad Cable (60-791) to a Concord Express, Concord, or Concord Ultra panel with the cable). Upon power up, the panel scans the bus for connecting the touchpad. Alphanumeric touchpads briefly show the date and time display. The following example...
Installation Instructions - Page 4
...arming/disarming the system, activating the touchpad panics, bypassing sensors, and by pressing 9 + user, partition, or system master CODE. The contrast adjustment lightens or darkens the text. Enter user programming mode by turning...unit number from Concord panel memory before activating alarms, to help compensate for lighting conditions in the section "Changing the Touchpad Unit Number."...
Installation Instructions - Page 5
...to a different number than all other bus devices.
Touchpad display appears blank, but beeps sound when buttons are pressed). Check the touchpad display contrast setting. To change the touchpad unit number (see procedure on this time, the touchpad is plugged in Concord RF systems. 5.
Press ƒ. Touchpad display shows a flashing *, indicating a trouble condition and system...
Installation Instructions - Page 6
... equipment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by GE Interlogix can be cleared. Concord is encouraged to try to part 15 of GE Interlogix. The touchpad and all applied for): .....UL 985 Household Fire Warning System Units UL 1023 Household Burglar-Alarm System Units...
Similar Questions
Keypad Beeping
Our keypad in our bedroom is starting to beep. It states that it might be a low battery but the powe...
Our keypad in our bedroom is starting to beep. It states that it might be a low battery but the powe...
(Posted by ziggybiggy 8 years ago)
My Ge Atp 1000 Keypad Gets Blazing Hot. It Is Newly Installed Over Heating Duct.
Is it defective or does it need to be moved? Why would this happen?
Is it defective or does it need to be moved? Why would this happen?
(Posted by Axelrod6 11 years ago)
How To Set Time And Date On Ge Atp-1000 Keypad
(Posted by melodale 11 years ago)
My Keypad Beeps 4xs A Day Every Min Until The Code Is Entered. How Do I Stop Thi
The chime goes off every minute until the code is entered at 8 am 4pm 6pm and 9pm everyday. How can ...
The chime goes off every minute until the code is entered at 8 am 4pm 6pm and 9pm everyday. How can ...
(Posted by nicholasadamsyoung 12 years ago)