GE ATP 1000 Support Question
GE ATP 1000 Support Question
Find answers below for this question about GE ATP 1000 - Security Concord Alphanumeric Touchpad.Need a GE ATP 1000 manual? We have 1 online manual for this item!
Question posted by nicholasadamsyoung on June 12th, 2011
My Keypad Beeps 4xs A Day Every Min Until The Code Is Entered. How Do I Stop Thi
The chime goes off every minute until the code is entered at 8 am 4pm 6pm and 9pm everyday. How can I stop this from happening.
Requests for more information
Request from thucdnguyen on September 9th, 2011 6:26 PM
Did you ever figure this out?
Did you ever figure this out?
Current Answers
Related GE ATP 1000 Manual Pages
Installation Instructions - Page 1
...touchpad illuminated from a button press
Typical operation
Power saving mode (no panel AC power)
Table 2: Maximum Touchpad...Mount the touchpad in speaker...security systems (see the "Specifications" section). The door can be removed by the touchpad. • Table 2 describes the maximum wire lengths allowed between the touchpad and the panel. Table 1: Touchpad...Touchpad Wire Length Between Touchpad...
Installation Instructions - Page 2
... plate with the wall or gang box screw holes and secure the
back plate using the screws provided. 5. Remove panel AC and backup battery power. 2. Be sure to open. For wall mounting, place the mounting plate on the touchpad and swing the touchpad bottom toward the mounting plate. Run a 4-conductor, 18- Installing the...
Installation Instructions - Page 3
... a Programming Touchpad-Concord Express Shown, Concord Similar
2. At the touchpad, enter program mode by pressing 8 + CODE + 0 + 2. The following example shows what a device address display may look like: UNIT - ATP1000 Touchpad/Display Installation Instructions
3 The touchpad should display SYSTEM PROGRAMMING.
4. Verify that don't include an alphanumeric touchpad as key beeps) see...
Installation Instructions - Page 4
... battery power. 2. Test the touchpad by arming/disarming the system, activating the touchpad panics, bypassing sensors, and by pressing 8 + installer/dealer CODE + 0 + 0 and program the panel using the panel Installation Instructions.
4. The display should read BUS DEVICES.
2. The contrast adjustment lightens or darkens the text.
Enter program mode by turning chime and lights on/off...
Installation Instructions - Page 5
... unit numbers to the desired unit number before applying power and entering program mode.
• Whenever possible, assign touchpad unit numbers before all other panel programming. The display should show DA n, where n is in .
3. Do not use unit number 15 in Concord RF systems. 5. Ignore the failure and continue with DIP switches (LED...
Installation Instructions - Page 6
...;2003 GE Interlogix.
These limits are designed to operate the equipment.
Compatibility Concord, Concord Express, Concord Ultra Power Requirements 12 VDC nominal (See Table 1 for additional power requirements... not installed and used by one touchpad, go to another system touchpad and enter 8 + installer/dealer CODE (default = 4321) + 0 + 1. The touchpad and all applied for): .....UL ...
Similar Questions
My Device Beeps Every 10 Mins?
How am I able to stop the device 5812-rnd from beeping every 10 mins
How am I able to stop the device 5812-rnd from beeping every 10 mins
(Posted by rbb5511 1 year ago)
Keypad Beeping
Our keypad in our bedroom is starting to beep. It states that it might be a low battery but the powe...
Our keypad in our bedroom is starting to beep. It states that it might be a low battery but the powe...
(Posted by ziggybiggy 8 years ago)
My Ge Atp 1000 Keypad Gets Blazing Hot. It Is Newly Installed Over Heating Duct.
Is it defective or does it need to be moved? Why would this happen?
Is it defective or does it need to be moved? Why would this happen?
(Posted by Axelrod6 11 years ago)
How To Set Time And Date On Ge Atp-1000 Keypad
(Posted by melodale 11 years ago)
I Have A Ge Atp 1000 Keypad. Can The Keypad Beeps Get Shut Off Or Lowered.
Also, is it possible to turning the beeping off when arming the system? Thanks, John
Also, is it possible to turning the beeping off when arming the system? Thanks, John
(Posted by jcangi01 12 years ago)