GE ATP 1000 Support Question
GE ATP 1000 Support Question
Find answers below for this question about GE ATP 1000 - Security Concord Alphanumeric Touchpad.Need a GE ATP 1000 manual? We have 1 online manual for this item!
Question posted by swuamett on July 23rd, 2012
P1 Code
I have a P1 code on my alarm panel and the chime continues to go off every minute or so. What is wrong and how do I correct this?
Current Answers
Related GE ATP 1000 Manual Pages
Installation Instructions - Page 1
... Usage
Current (mA) 110
60 12
Conditions
Maximum alarm current with basic system operating commands. A built-in an environmentally controlled area (32°F to 120°F/0°C to indicate the current status of compatible security systems (see the "Specifications" section). Touchpad Wire Length Between Touchpad and Panel
750 feet 300 feet
1 A swingdown door reveals a label...
Installation Instructions - Page 2
... or gang box screw holes and secure the
back plate using the screws provided. 5. Separating the Touchpad from the panel to the touchpad location (see Figure 1). Figure 2. Loosen screw,
then lift touchpad. Be sure to leave a 3-inch clearance below for touchpad terminal identification). Wiring the Touchpad to open. Touchpad Wiring Connections
Attaching the Touchpad to 22-gauge wire from...
Installation Instructions - Page 3
....DSF
Figure 4.
Verify that don't include an alphanumeric touchpad as a programming touchpad, be careful not to a Concord Express, Concord, or Concord Ultra panel with the cable). The touchpad should read BUS DEVICES.
6. Press A or B to cycle through 9 are ready to power up the panel and verify correct communication between the panel and touchpad is also located on a label on the...
Installation Instructions - Page 4
....
2.
Enter user programming mode by turning chime and lights on/off to avoid dispatching local police and fire departments. Press , and the display briefly shows DONE, then shows the time and date.
4
ATP1000 Touchpad/Display Installation Instructions Enter a setting from Concord panel memory before activating alarms, to verify correct operation. The display shows DA nnn.
2. The...
Installation Instructions - Page 5
...a flashing *, indicating a trouble condition and system doesn't respond to do if the touchpad does not operate correctly. Relocate transformer to exit from touchpad.
1. Note At this page). (Concord panels with software versions 1.01.6 only.)
Changing the Touchpad Unit Number (Concord
Panels with Software Version 1.0-1.6 Only)
Use the following guidelines when changing device unit numbers to...
Installation Instructions - Page 6
... only installed touchpad, remove panel AC and battery power, then re-apply power.
Compatibility Concord, Concord Express, Concord Ultra Power Requirements 12 VDC nominal (See Table 1 for help.
)
©2003 GE Interlogix. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by any bus failures should operate correctly and...
Similar Questions
Once Set, How Do You Change The Security Code On The System?
(Posted by ataylor356 9 years ago)
My Keypad Beeps 4xs A Day Every Min Until The Code Is Entered. How Do I Stop Thi
The chime goes off every minute until the code is entered at 8 am 4pm 6pm and 9pm everyday. How can ...
The chime goes off every minute until the code is entered at 8 am 4pm 6pm and 9pm everyday. How can ...
(Posted by nicholasadamsyoung 12 years ago)
How Do We Disarm Our System And When Do We Type In Security Code?
(Posted by carolyn2707 13 years ago)
P1
what does p1 on the display mean? it was never there before and now it is.
what does p1 on the display mean? it was never there before and now it is.
(Posted by stepharice 13 years ago)