GE ATP 1000 Support Question
GE ATP 1000 Support Question
Find answers below for this question about GE ATP 1000 - Security Concord Alphanumeric Touchpad.Need a GE ATP 1000 manual? We have 1 online manual for this item!
Question posted by carolyn2707 on January 22nd, 2011
How Do We Disarm Our System And When Do We Type In Security Code?
The person who posted this question about this GE product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related GE ATP 1000 Manual Pages
Installation Instructions - Page 1
...;C to indicate the current status of compatible security systems (see the "Specifications" section). The door can also be activated anytime.
See the panel installation instructions for cutting wallboard
Guidelines
• Mount the touchpad in speaker provides alarm, status, and button-press sounds. Touchpad Wire Length Between Touchpad and Panel
750 feet 300 feet
1
A swingdown...
Installation Instructions - Page 2
... the screw into the wall at the top of the mounting plate with the wall or gang box screw holes and secure the
back plate using the screws provided. 5. Separating the Touchpad from mounting properly.
Align the mounting plate holes with the slots on the wall and mark the mounting holes (see...
Installation Instructions - Page 3
... ta y 2
S ile n t 5
S y s te m 8
L ig h ts 0
A w ay 3
P ag e r 6
M enu 9
B yp ass #
PROGRAMMING TOUCHPAD CABLE (60-791)
8642G29A.DSF
Figure 4. Alphanumeric touchpads briefly show the date and time display. Press A or B to a Concord Express, Concord, or Concord Ultra panel with the cable). To connect a programming touchpad to cycle through 9 are ready to power up , connect the cable to...
Installation Instructions - Page 4
...UNIT -
Test the touchpad by arming/disarming the system, activating the touchpad panics, bypassing sensors, and by pressing 9 + user, partition, or system master CODE. Refer to verify... shows the time and date.
4
ATP1000 Touchpad/Display Installation Instructions Press D to a Concord panel with software versions 1.0-1.6 display USER CODES.)
2. To adjust display brightness:
1. Press...
Installation Instructions - Page 5
...'t power up (no display and no longer communicating to do if the touchpad does not operate correctly.
Check for at touchpad and panel terminals.
2. Check the touchpad display contrast setting. Make sure touchpad unit number is in Concord RF systems. 5. The display should show DA n, where n is not plugged into an electrical outlet controlled by...
Installation Instructions - Page 6
... Installation Instructions Concord is the only installed touchpad, remove panel AC and battery power, then re-apply power. FCC Part 15 Class B
This equipment has been tested and found to another system touchpad and enter 8 + installer/dealer CODE (default = 4321) + 0 + 1. For systems with more information on different branch circuits. ‰ Consult the dealer or...
Similar Questions
How To Access The Dealer Code On Concord Express
(Posted by zacShinNe 9 years ago)
How To Reset Security Code Ge Concord Express
(Posted by bahstevej 10 years ago)
P1 Code
I have a P1 code on my alarm panel and the chime continues to go off every minute or so. What is wro...
I have a P1 code on my alarm panel and the chime continues to go off every minute or so. What is wro...
(Posted by swuamett 11 years ago)
My Keypad Beeps 4xs A Day Every Min Until The Code Is Entered. How Do I Stop Thi
The chime goes off every minute until the code is entered at 8 am 4pm 6pm and 9pm everyday. How can ...
The chime goes off every minute until the code is entered at 8 am 4pm 6pm and 9pm everyday. How can ...
(Posted by nicholasadamsyoung 12 years ago)